Gardsman CTC-1052 Скачать руководство пользователя страница 6

  Insert the SIM card with the chip side facing 

up. 

 

  Push  to  the  furthest  extend,  then  press  on 

the edge of the SIM card firmly to secure it. 

  SIM  Card  will  delete  its  SMS  message 

whenever the CTC-1052 is powered on.  

 

 

To remove SIM card: 

Press and release on the edge of SIM card, the 
card will spring out. 

 

1.4. How to install the Control 

Panel 

Locating  a  suitable  position  for  the 
Control Panel 

 

The Control Panel requires main power and 
a constant GPRS/3G/LTE reception. 

 

The  Control  Panel  should  be  easily 
accessible. 

 

The  Control  Panel  should  not  be  placed  in 
a damp location, such as a bathroom. 

 

The  Control  Panel  should  not  be  placed 
close  to  any  heat  source,  such  as 
microwave ovens, which can reduce signal 
strength. 

 

The  Control  Panel  should  not  be  located 
alongside  other  radio  transmitting  devices, 
such as mobile phones, cordless phone, or 
wireless computer network (Wi-Fi) devices. 

 

Important: When drilling into a wall, ensure 
there are no hidden cables or pipes. 

 

Mounting the Control Panel 

The  Control  Panel  can be  mounted  on  the  wall 
or wherever desired (e.g. on the table).  Ensure 
the Control Panel is fitted at approximately chest 
height  where  the  buttons,  microphone,  and 
speaker can be easily accessed and operated. 

  Use  the  2  holes  of  the  Wall  Mounting 

Bracket  as  a  template,  mark  off  the  holes’ 
positions. 

  Drill  2  holes  and  insert  the  wall  plugs  if 

fixing into plaster or brick. 

  Screw the base to the wall. 

  Hook  the  Control  unit  onto  the  Wall 

Mounting Bracket (holding the unit with the 
front facing you).  

 

1.5. Compatible with Climax’s 

SMS Editor  

 

CTC-1052  is  compatible  with  Climax’s  SMS 
Editor,  which  is  designed  to  facilitate  SMS 
remote programming via a PC. This tool allows 
you  to  program  the  panel  easily  from  your 
computer,  without  sending  complex  SMS  text 
messages from a mobile phone.

 

 

Содержание CTC-1052















































Отзывы: