FUTABA 8US Скачать руководство пользователя | Manualshive

Страница: 50 / 99

background image

47

You can use Throttle Curve menus to program a five-point curve so that the

engine speed responds the way you like relative to movement of the throttle stick.
You can set each of the five points over a 0% to 100% range.

There are three throttle curves: normal (NORM), idle-up 1 (IDL1), and idle-up 2

(IDL2).    Only the basic normal throttle curve is displayed in the Basic Menu, but all
the curves may be programmed in the Advance Menu.    For your convenience, the
normal curve can be programmed in either the Basic or Advance Menu, and it is
automatically updated in both places.    Switch G is programmed so that you may
change between the normal (NORM), idle-up 1 (IDL1), and idle-up 2 (IDL2) curves.

The normal throttle curve (TH-CRV NORM) function is used to produce the basic
throttle curve for flight near hover. It is used along with the normal pitch curve (PI-
CRV NORM) so that the helicopter flies with constant rotor RPM. The normal
throttle curve function is ON at startup.

The idle-up curves should be programmed so that the engine maintains constant RPM
even when the pitch is reduced during flight. The curves should be matched to loops,
rolls, and other maneuvers, and are divided into idle-up curve 1 and idle-up curve 2.
The TH-CURV functions for IDL1 and IDL2 curves will not operate until the OFST-1
and OFST-2 functions are activated.

LOW

throttle stick

HI

100

75%

50%

25%

0%

S

e

rv

o R

e

s

pons

e

LOW

throttle stick

HI

100

75%

50%

25%

0%

S

e

rv

o R

e

s

pons

e

Throttle Curve IDL1 Example

Throttle Curve IDL2 Example

Throttle Curve Norm Example

LOW

throttle stick

HI

100

75%

50%

25%

0%

S

e

rv

o R

e

s

pons

e

1

2

3

4

5

Curve Point

70%

50%

30%

0%

75%

50%

75%

68%

68%

71%

55%

60%

1

2

3

4

5

Curve Point

1

2

3

4

5

Curve Point

«
...
48
49
50
51
52
...
»

Содержание 8US




































































































Отзывы:

Нет отзывов

Похожие инструкции для 8US

Бренд: GARAN Страницы: 8

Бренд: Walimex Pro Страницы: 68

Бренд: K'Nex Education Страницы: 56

Бренд: Rane Страницы: 2

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: WAGO Страницы: 16

Total Access 351 Series

Бренд: ADTRAN Страницы: 4

Centronic SunWindControl SWC245-II

Бренд: Becker Страницы: 52

Бренд: IR-Tec Страницы: 14

Бренд: Spirax Sarco Страницы: 24

Бренд: Precision Страницы: 8

TRAP-SHUFFLE Game Simulator

Бренд: RF SOLUTIONS Страницы: 2

Бренд: Gardigo Страницы: 12

Бренд: V2 Страницы: 180

Бренд: EasyCare Страницы: 26

AWH18QD-D3DNA3G/I

Бренд: AC Pro Страницы: 48

Бренд: CompuSTAR Страницы: 8

Бренд: RC-Timing Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды