FUTABA 8US Скачать руководство пользователя | Manualshive

Страница: 93 / 99

background image

-90-

90

The Speed function is used to offset

the aileron, elevator, and flap servos to the
position that provides maximum drag for
cruise and high-speed flight.    Normally
the ailerons and flaps are raised about 3-
5°.    Some airfoils, notably the RG-15,
actually have higher drag with reflex, so
Speed function should not be used with
this section and other similar ones.    The
elevator neutral can also be offset in order
to trim out any pitch changes caused by
the trailing edge reflex.    This function is
activated by flipping switch G to the
forward position.

If you wish to have the three-position

switch above the left-hand stick (position
E), you should purchase the 8UH system.

Speed presets

Inputting the Speed presets for your model

To PMIX-1 function

To START function

Channel
being offset
for START

2. Aileron 1 offset
Input the desired Aileron 1
offset with the (+)/(-) keys.
3. Elevator offset
Input the desired Elevator
offset with the (+)/(-) keys.
4. Flap offset*
Input the desired Flap offset
with the (+)/(-) keys.
5. Aileron 2 offset
Input the desired Aileron 2
offset with the (+)/(-) keys.

(You may reset to zero by
pressing the (+)/(-) keys
simultaneously.)

Data input keys

These keys are used to move through the

five submenus in the SPEED function.

Turn the SPEED function ON by pressing the (+)
key ("ON" or "OFF" displayed depending on
Switch G position). Turn off (INH) the function
with the (-) key.

Servo offset
Range: -100 to +100%
Initially set to 0%

*The GLID 2FLP menu for SPEED has
separate Flap 1 and Flap 2 offsets.

«
...
91
92
93
94
95
...
»

Содержание 8US




































































































Отзывы:

Нет отзывов

Похожие инструкции для 8US

Бренд: NEJE Страницы: 17

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: ICM Controls Страницы: 2

Бренд: M-system Страницы: 3

Бренд: RKC INSTRUMENT Страницы: 10

SAE 07.2 Series

Бренд: AUMA Страницы: 116

Бренд: Parallel Audio Страницы: 4

Бренд: MELICONI Страницы: 6

Бренд: Eazyzap Страницы: 32

Бренд: salmson Страницы: 33

Бренд: Festo Страницы: 12

Бренд: Inovance Страницы: 2

Бренд: Azbil Страницы: 12

CPVSC1-M1H-D-H-M5C

Бренд: Festo Страницы: 2

Бренд: Mami Страницы: 2

Бренд: Oasis Страницы: 8

Videoconferencing system

Бренд: PictureTel Страницы: 122

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды