FUTABA 8US Скачать руководство пользователя | Manualshive

Страница: 51 / 99

background image

48

Inputting the Throttle Curve in Normal, Idle-up 1, and Idle-up 2

CAUTION
Before actually starting the engine, be sure that idle-up switches 1 and 2 are off, and the
throttle is set near engine idle.

To TH-CRV
IDL1 function

To PI-CRV
NORM function

Data input keys

These keys are used
to move through the
five submenus in the
TH-CRV function.

The bottom arrow shows the point
on the five-point curve currently
being set.

Top arrow indicates the current stick
position (2 arrows means it's between
points)

Curve points 1-5

Curve Name
Display
(NORM)

Input 5-point curve values
Move the lower arrow to the
position you want to set with the
CURSOR keys (the curve point is
indicated by the arrow below the
numbers 1-5, and the current
throttle position is above the
numbers). Enter the desired curve
value with the (+)/(-) keys.
• If you're unhappy with what you've
set, you may return to the default
value by pressing the (+) and (-)
keys simultaneously.

Curve Point Value
(Range: 0 - +100%)
Initial curve settings:
POS1 = 0%
POS2 = 25%
POS3 = 50%
POS4 = 75%
POS5 = 100%

The Throttle Curve Normal function is on at startup.

The blinking item on the
setting screen is the
current setting item.

Idle-up 1 Curve Setting
The TH-CRV IDL1 function will not operate until the OFST1
function is activated.    This also activates the IDL1 Pitch &
REVOLU curve menus.    You can    activate idle-up 1 and idle-up 2
independently.
The curve setting procedure is the same as normal curve
described above.

To TH-CRV IDL2 function

To TH-CRV function

Idle-up 2 Curve Setting
The TH-CRV IDL2 function will not operate until the OFST2
function is activated. This also activates the IDL2 Pitch &
REVOLU curve menus.
The curve setting procedure is the same as normal curve
described above.
You can activate idle-up 1 and idle-up 2 setups independently.

To TH-HLD function

To TH-CRV IDL1 function

«
...
49
50
51
52
53
...
»

Содержание 8US




































































































Отзывы:

Нет отзывов

Похожие инструкции для 8US

DELTAFLUX MT100

Бренд: PIETRO FIORENTINI Страницы: 16

Бренд: D-Link Страницы: 6

Бренд: B meters Страницы: 2

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 12

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 8

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 14

Бренд: FAAC Страницы: 68

Real Living iM1

Бренд: Yale Страницы: 2

Бренд: 2gig Technologies Страницы: 6

Бренд: IR-Tec Страницы: 14

Бренд: HEROSE Страницы: 92

Бренд: netvox Страницы: 12

RC Electronic DPSI LCD

Бренд: Emcotec Страницы: 32

Бренд: Danfoss Страницы: 4

Бренд: Watts Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды