FUTABA 8US Скачать руководство пользователя | Manualshive

Страница: 10 / 99

background image

7

Specifications and ratings are subject to change without notice.

x

8UH Transmitter, including RF module

x

R148DP/DF Receiver, R138DP/DF, or R149DP Receiver

x

Servos, five S3001 , five S9202, four S3001, or four S9001, with mounting hardware and

servo arm assortment

x

Switch harness

x

Extension cord

Transmitter T8UHFS/HPS (Helicopter

Version)

Operating system: 2-stick, 8 channels,

PCM1024 system

Transmitting frequency: 29, 35, 36, 40, 41, 50,

60 or 72 MHz bands

Modulation: FM/PPM or PCM, switchable
Power supply: 9.6V NT8S600B Ni-Cd battery
Current drain: 250 mA

Receiver R148DP/DF (PCM or FM

Dual conversion)

Receiving frequency: 29, 35, 36, 40, 41, 50,

60 or 72 MHz bands

Intermediate freq.: 10.7 MHz and 455 kHz
Power requirement: 4.8V Ni-Cd battery
Current drain: 14 mA
Size: 2.19 x 1.00 x 0.89” (55.5 x 25.5 x

22.5 mm)

Weight: 1.07 oz (30.4 g)

Servo S9202 (Coreless, ball-bearing)

Control system: Pulse width control, 1.52 ms

neutral

Power requirement: 4.8V (from receiver)
Output torque: 69.5 oz-in (5.0 kg-cm)
Operating speed: 0.22 sec/60°
Size: 1.59 x 0.79 x 1.40” (40.4 x 19.8 x 36 mm)
Weight: 1.7 oz (48.2 g)

Servo S3001 (Standard, ball-bearing)

Control system: Pulse width control, 1.52

ms neutral

Power requirement: 4.8V (from receiver)
Output torque: 41.7 oz-in (3.0 kg-cm)
Operating speed: 0.22 sec/60°
Size: 1.59 x 0.78 x 1.41” (40.4 x 19.8 x 36

mm)

Weight: 1.59 oz (45.1g)

x

Memory module – the optional DP-16K

doubles your model storage capability (to 16

models from 8) and allows you to transfer programs to another 8UH transmitter.

x

Transmitter battery pack – the NT8S600B transmitter Ni-Cd battery pack may be easily

exchanged with a fresh one to provide enough capacity for extended flying sessions

x

Trainer cord – the optional training cord may be used to help a beginning pilot learn to fly

easily by placing the instructor on a separate transmitter. Note that the 8UH transmitter may
be connected to another 8UH/8UA system, as well as to any F5, Skysport, Super 7, or 9Z
series transmitter.

x

Neckstrap – a neckstrap may be connected to your 8UH system to make it easier to handle

and improve your flying precision, since your hands won’t need to support the transmitter’s
weight

«
...
8
9
10
11
12
...
»

Содержание 8US




































































































Отзывы:

Нет отзывов

Похожие инструкции для 8US

Бренд: Valve Concepts Страницы: 16

Бренд: Samson Страницы: 36

Бренд: CAME Страницы: 4

Бренд: QUNDIS Страницы: 2

Бренд: Össur Страницы: 58

Бренд: Runxin Страницы: 4

Samos Pro Compact SP-COP2

Бренд: Wieland Страницы: 36

Бренд: Colorbeam Страницы: 12

Бренд: Eazyzap Страницы: 32

Бренд: Danfoss Страницы: 124

Бренд: ROTORCOMP Страницы: 50

SHIELD-LORA-RFM

Бренд: Cytron Страницы: 10

Бренд: Fuzik Страницы: 16

Бренд: Eurotronic Страницы: 5

Бренд: Sentiotec Страницы: 12

Бренд: SimCom Страницы: 19

Бренд: Pentair Страницы: 13

Price Center 451

Бренд: Polycom Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды