Configuring the Subwoofer for 2.1 Operation
The subwoofer features dual 2 Ohm voice coils and is pre-
configured for 4 Ohm operation. You can change the
configuration of the subwoofer for 2.1 operation (two speakers
and one subwoofer) when connected to a FUSION stereo with
DSP capability, such as an Apollo
™
RA770.
1
Disconnect the gray wire and the white with a black stripe
wire from the jumper terminals on the back of the subwoofer.
2
Connect the wires from the subwoofer to the stereo using the
following table as a reference.
Subwoofer wire
Stereo wire
White
Zone 2 right positive (+)
White with a black stripe
Zone 2 right negative (-)
Gray
Zone 2 left positive (+)
Gray with a black stripe
Zone 2 left negative (-)
3
Turn on the connected stereo.
4
Launch the FUSION-Link
™
app, and select the 2.1 option for
the connected stereo.
The subwoofer operates in 2.1 mode, with the volume control
tied to zone 1 on the stereo. The zone 2 volume control and the
zone 2 line out connectors are disabled.
Additional Information
True-Marine
™
Products
True-Marine products are subjected to rigorous environmental
testing under harsh marine conditions to surpass industry
guidelines for marine products.
Any product that bears the True-Marine stamp of assurance has
been designed for simplicity of use and combines advanced
marine technologies to deliver an industry leading entertainment
experience. All True-Marine products are supported by the
FUSION 3-year worldwide limited consumer warranty.
Registering Your XS Series
Help us better support you by completing our online registration
today.
• Go to
www.fusionentertainment.com
.
• Keep the original sales receipt, or a photocopy, in a safe
place.
Cleaning the Subwoofer
NOTICE
Do not use harsh or solvent-based cleaners on the subwoofer.
Using such cleaners may damage the product and void the
warranty.
When mounted correctly, this subwoofer is rated IP65 for
protection in the harsh marine environment from the front of the
subwoofer. The subwoofer is not designed to withstand high
pressure water spray, which may occur when you wash down
your vessel. Failure to carefully spray-clean the vessel may
damage the product and void the warranty.
1
Clean all salt water and salt residue from the grille with a
damp cloth soaked in fresh water.
2
Use a mild detergent to remove a heavy buildup of salt or
stains.
Troubleshooting
Before you contact your FUSION dealer or service center, you
should perform a few simple troubleshooting steps to help
diagnose the problem.
If the FUSION subwoofer has been installed by a professional
installation company, you should contact the company so the
technicians can assess the problem and advise you about
possible solutions.
There is no sound coming from the subwoofer
• Verify that all connections are connected correctly to the
proper terminals.
The system lacks bass
• Verify that the subwoofer is attached firmly to the mounting
surface.
The audio is distorted
• Verify that the panels surrounding the subwoofer on the
vessel are not rattling.
• Verify that the amplifier is connected to the subwoofer
terminals correctly.
• If the subwoofer is connected to an amplifier, verify that the
input level of the amplifier is matched to the output level of
the stereo.
For more information, see the manual for the amplifier.
The LED lights will not turn on
• Verify that all wiring connections are correct and tight.
The LEDs pulse with the bass notes of the music
• Install a FUSION LED voltage regulator (SG-VREGLED).
Specifications
Peak power (Watts)
600 W
RMS power (Watts)
120 W
Efficiency (1 W/1 m)
87 dB
Frequency response
From 30 Hz to 2000 Hz
Nominal impedance
4 ohm
Recommended amplifier power
(RMS)
40 to 300 W per channel
Min. mounting depth (clearance)
113 mm (4
7
/
16
in.)
Mounting diameter (clearance)
223 mm (8
3
/
4
in.)
Optimum enclosure volume
recommendation*
40 L
LED color options (sports model only) RGB
LED supply voltage (Sports model
only)
From 10.8 to 16 Vdc
LED load current at 14.4 Vdc (Sports
model only)
150 mA
Operating temperature range
From 0 to 50°C (from 32 to
122°F)
Storage temperature range
From -20 to 70°C (from -4 to
158°F)
Cone/surround material
Polypropylene cone, rubber
surround
Water and dust rating
IEC 60529 IP65 (Protected
against dust and water ingress)
*Sealed enclosure, fully filled with absorption material.
NOTE:
This speaker is not intended to be installed in a vented
or ported enclosure when exposed to the outside environment.
Speaker Dimensions
4
Installation Instructions
