Furuno FCV-1900/B/G Скачать руководство пользователя страница 35

Страница: 35 / 52

3. INITIAL SETTINGS

5. Turn the processor unit on.

The message shown below appeared when the system is lower than the upgrade
key.

Note:

When the upgrade key is a grade lower than the key in processor unit, the

processor unit starts normally and no upgrade system message is displayed.

6. Rotate the

ENTER

knob to select [Yes] and push the knob.

The upgrading starts automatically and the system is restarted.

7. Press the

MENU/ESC

key to display the [Setting] menu.

8. Rotate the

ENTER

knob to select [System], then push the knob.

9. Rotate the

ENTER

knob to select [Test], select [Diagnostic Test], then push the

knob.
The diagnostic test window appears.

10. At the first line of the [Display unit] section of the test result, confirm that the up-

grading is complete. “Product Grade” shows FCV-1900B or FCV-1900G depend-
ing on the upgrade.

11. Press the

MENU/ESC

key three times to close the test window.

12. Press the

MENU/ESC

key several times to close the menu.

13. Turn the processor unit off and then remove the USB flash memory.

Upgrade system?

Yes

Press the camera icon key 3 times to capture. (1/99)

Press the [MENU/ESC] key 3 times to exit.

Display Unit

Product Grade :

FCV-1900

MAC Address :

00-40-9D-7D-9D-32

IP Address :

172.31.92.7

CPU Status :

Application Ver :

0252434-xx.xx

System Ver :

0252437-xx.xx

Kernel Ver :

0252436-xx.xx

Fan Speed :

5160rpm

U-Boot Ver :

0252435-xx.xx

PIC Boot Ver :

1950143-xx.xx

PIC Main Ver :

1950144-xx.xx

Signal Unit

Fish Finder Sensors

ROM :

RAM :

MAC Address :

00-D0-1D-0C-A5-31

IP Address :

172.31.92.6

Power Voltage(12V) : 12.1V

Power Voltage(5V) : 5.0V

HF BVolt :

120.9V

LF BVolt :

113.2V

PWR Board Ver :

CTRL Board Ver :

TRX Board Ver :

Application Ver :

0252425-xx.xx

FPGA Ver :

0252426-xx.xx

Boot Ver :

0252424-xx.xx

Start Ver :

0252423-xx.xx

Fan Speed :

8640.0rpm

Port1(NMEA1) :

Port2(NMEA2) :

Port3(Tankenmaru) : --

Port4(SC) :

Port5(CIF) :

Telesounder :

Temp :

10.4ºC

ROM :

RAM :

Application Ver :

xxxxxxxxxx

Boot Ver :

xxxxxxxxxx

Temp :

10.4ºC

xx.xx: Program version

Product
grade

Содержание FCV-1900/B/G





















































Результаты поиска

Содержание FCV-1900/B/G

Отзывы:

Похожие инструкции для FCV-1900/B/G

Бренды по названию

Популярные бренды

Furuno FCV-1900/B/G, Руководство по установке

Результаты поиска

Содержание FCV-1900/B/G

Отзывы:

Похожие инструкции для FCV-1900/B/G

Бренды по названию

Популярные бренды