Fujitsu PRIMERGY TX2550 M5 Скачать руководство пользователя страница 80

Страница: 80 / 106

Operating Manual

TX2550 M5

Operation

6.2

Access to the drives (floorstand model)

6.2.1

Removing the drive covers

Figure 18: Removing the accessible drive bay cover

Turn the key clockwise (1) to unlock the accessible drive cover and remove
the key.

Depending on the setting of the green hook in the accessible drive
bay cover, you can open the drive cover without turning the key or
only with turning the key.

Open the accessible drive bay cover carefully in the direction of the arrow
(2) until the cover is released and remove it.

CAUTION!

Do not pull too hard to avoid damage to the locking mechanism.

Place the accessible drive bay cover on the HDD bay cover (3).

Push the accessible drive bay cover in the direction of the arrow (4).

Содержание PRIMERGY TX2550 M5











































































































Результаты поиска

Содержание PRIMERGY TX2550 M5

Отзывы:

Похожие инструкции для PRIMERGY TX2550 M5

Бренды по названию

Популярные бренды

Fujitsu PRIMERGY TX2550 M5, Руководство по эксплуатации

Результаты поиска

Содержание PRIMERGY TX2550 M5

Отзывы:

Похожие инструкции для PRIMERGY TX2550 M5

Бренды по названию

Популярные бренды