Fujitsu PRIMERGY TX2550 M5 Скачать руководство пользователя страница 72

Страница: 72 / 106

Operating Manual

TX2550 M5

Starting up

5.7

Configuring the server with ServerView
Installation Manager

Ensure that the power saving functions are disabled in the Power menu
of the BIOS setup during operation.

Advantages of the ServerView Installation Manager

– Wizard-assisted configuration of your server hardware and disk arrays.

– Wizard-assisted installation of all leading server operating systems.

– Wizard-assisted creation of configuration files for unattended installation of

several PRIMERGY servers with identical hardware configurations.

– Installation of drivers and additional software.

The software that can be installed depends on the hardware
configuration of your server. This configuration is detected automatically.

5.7.1

Configuring the server and installing the operating
system

When using the ServerView Installation Manager you can configure the
onboard controller either before or during installation.

Descriptions of operating systems not covered in the RAID controller
manual are provided in the corresponding readme files under:

http://www.fujitsu.com/global/services/computing/server/ia/driver/index.
html

For Japan:

http://www.fujitsu.com/jp/products/computing/servers/primergy/downloa
ds/

Содержание PRIMERGY TX2550 M5











































































































Результаты поиска

Содержание PRIMERGY TX2550 M5

Отзывы:

Похожие инструкции для PRIMERGY TX2550 M5

Бренды по названию

Популярные бренды

Fujitsu PRIMERGY TX2550 M5, Руководство по эксплуатации

Результаты поиска

Содержание PRIMERGY TX2550 M5

Отзывы:

Похожие инструкции для PRIMERGY TX2550 M5

Бренды по названию

Популярные бренды