Fujitsu PRIMERGY TX2550 M5 Скачать руководство пользователя страница 30

Страница: 30 / 106

Operating Manual

TX2550 M5

Product description

3.3.2.2

Indicators on the front panel

Figure 8: Indicators on the front panel module

ID button

Highlights the ID indicator on the front panel
and I/O panel for easy server identification.

On/Off
button

Used to switch the server on or off.

If the system is running an ACPI-
compliant operating system, pressing
the On/Off button will perform a
graceful shutdown.

Pos. Label

Indicator

Status

Description

ID
indicator,
see also

blue on

The server has been highlighted
using ServerView Operations
Manager, iRMC web interface or the
ID button on the front panel for easy
identification.

flashing
blue

The server has been highlighted for
easy identification using the iRMC
with disabled local VGA output.

Pos.

Label

Button

Function

Содержание PRIMERGY TX2550 M5











































































































Результаты поиска

Содержание PRIMERGY TX2550 M5

Отзывы:

Похожие инструкции для PRIMERGY TX2550 M5

Бренды по названию

Популярные бренды

Fujitsu PRIMERGY TX2550 M5, Руководство по эксплуатации

Результаты поиска

Содержание PRIMERGY TX2550 M5

Отзывы:

Похожие инструкции для PRIMERGY TX2550 M5

Бренды по названию

Популярные бренды