Fujitsu PRIMERGY TX2550 M5 Скачать руководство пользователя страница 31

Страница: 31 / 106

TX2550 M5

Operating Manual

Product description

[CSS]

CSS
indicator

off

No critical event detected (CSS
component).

orange
on

Prefailure event detected (CSS
component).

For HDDs/SSDs, see also

"HDD/SSD prefailure detection" on
page 33

flashing
orange

CSS component failure detected.

Global
Error
indicator,
see also

off

No critical event detected (non CSS
component).

orange
on

Prefailure event detected (non CSS
component).

flashing
orange

Non CSS component failure
detected.
Possible causes:

– System is out of the specified

temperature range

– Defective sensor
– CPU error
– Error detected by server

management software

HDD/SSD
activity
indicator

flashing
green

Data access in progress.

Power-on
indicator

off

The server is switched off.

green on

– The server has been switched on

but Power Cycle Delay settings
delay it from turning on for a
specified time.

– The server is switched on and

operating normally.

flashing
green
slowly

The BMC firmware is starting up after
the server has been connected to the
mains.

Pos. Label

Indicator

Status

Description

Содержание PRIMERGY TX2550 M5











































































































Результаты поиска

Содержание PRIMERGY TX2550 M5

Отзывы:

Fujitsu PRIMERGY TX2550 M5, Руководство по эксплуатации, Страница: 31 / 106

Результаты поиска

Содержание PRIMERGY TX2550 M5

Отзывы: