Fujian Xingyi Polishing Machine 800-4E Скачать руководство пользователя

Страница: 57 / 65

Fujian Xingyi Polishing Machine Co.,Ltd

Manual Of Remote Control Floor Grinder 800-4E

Factory Addresss:NO.C2 ,Area 11 ,AnPing Development Area, Quanzhou ,Fujian province ,China

Postal Code:362200

Tel: +86-595-36792992

Mob: +86-15960788816

www.xy1118.com

Use only Xingyi parts and accessories, For your own safety, The Safety of others and the life of your machines.

、

Frequently Asked Questions and Solutions

This chapter describes some of the possible failures and how to handle them. If you still

can not resolve or have an error, please contact your nearest retailer.

Problem

Potential cause

Solution

The machine does not start

The emergency stop switch is

pressed

Open the emergency stop switch

overloading

Unplug the power plug directly and insert
again.

Power and power cables are

damaged

Contact licensed electrician

The switch knob of machine is

damaged

Make sure the wires are properly
connected to the rear button, check the
contacts with the ignition button

Output voltage does not match

Adjust matchable voltage

Improper wiring

Check the wiring and terminal of power
input

The Inverter is damaged

Repair or replace the inverter

The motor is damaged

Repair or replace the motor

The machine uttered a low buzz when

turn on and turn off

There is dust in the motor

impeller

Contact licensed electrician

Motor burnt out

Contact licensed electrician or Check
whether the input p

Phase loss input, currently only

two phase inputs. Turn off the

machine to avoid burning the

motor

Contact licensed electrician or Check
whether the input power is three-phase

The machine is difficult to control or

the motor current is consumed

The machine below the diamond

is too small or the wrong tool

type is applied

Use xingyi recommend numbers of
diamonds to reduce the stress on the
grinder and the operator

Machine beating unevenly

Diamond may not be properly

installed or highly different

Properly install diamonds with the same

height

The chassis is flat or not

Adjust the installed chassis

Machine forward, backword out of

control

machine clutch key is break or

there is no clutch

change or install new clutch key

check the PLC is running or not

contact with factory to repair

cable is loose or not

Contact licensed electrician

wheel or drive connector key is

damage or not

check and contact with factory to repair

and change the key

The speed of machine can’t be

1.Reinstall inverter parameters

Содержание 800-4E


































































Результаты поиска

Содержание 800-4E

Отзывы:

Похожие инструкции для 800-4E

Бренды по названию

Популярные бренды

Fujian Xingyi Polishing Machine 800-4E, Руководство пользователя

Результаты поиска

Содержание 800-4E

Отзывы:

Похожие инструкции для 800-4E

Бренды по названию

Популярные бренды