Fuji Xerox DocuPrint C1110 B страница 105 Скачать руководство пользователя | Manualshive

Страница: 105 / 209

background image

6.2 Hardware Problems (Power Failure, Abnormal Noise, etc.)

105

6.2

Hardware Problems
(Power Failure, Abnormal Noise, etc.)

Symptom

Cause/Remedy

The printer will not switch on.

Is the power switched on?
Switch the power on by pressing the power switch to the <|> position.

Is the power cord firmly plugged into the power outlet?
Switch the power off, plug the power cord firmly into the power connector or power
outlet, and switch the power back on.

Is the printer plugged into a power outlet that supplies proper voltage?
Connect the printer to a power outlet that supplies the proper rated voltage or current.
And do not share the power outlet with other devices.

The display is blank.

The printer may be in the Power Saver mode. Press the <Power Saver> button on the
control panel to exit the Power Saver mode.
If this does not remedy the problem, check if the power cord is firmly plugged into the
power outlet, and reboot the printer.
If the problem still persists, the printer may be at fault. Contact our Customer Support
Center or your dealers.

The printer makes odd noise.

Is the printer installed on a level surface?
Move the printer on a level and sturdy surface.

Is the paper tray pushed in completely?
Push the tray firmly into the printer.

A foreign object may be in the printer.
Switch the power off and remove the object. If the object cannot be removed without
dismantling the printer, contact our Customer Support Center or your dealers.

Dew condensation formed in
the printer.

On the control panel, set the interval that the printer switches to the Sleep mode to
more than 60 minutes, and let the printer stand with its power on. After about an hour,
the condensation disappears due to the heat inside the printer.

Refer to

• Sleep mode: [System Settings] (P. 90)

The printer does not switch to
the Sleep mode.

Isn't the Sleep mode disabled?
On the control panel, set [Sleep Mode] to [Enable].
The Sleep mode cannot be disabled on the Chinese model.

«
...
103
104
105
106
107
...
»

Содержание DocuPrint C1110 B


















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint C1110 B

Бренд: Xante Страницы: 21

Бренд: Canon Страницы: 37

Бренд: Oki Страницы: 197

Бренд: Partner Страницы: 15

Бренд: Posnet Страницы: 2

Бренд: A&D Страницы: 8

Бренд: Xerox Страницы: 8

Бренд: UVP Страницы: 22

Бренд: Microcom Страницы: 207

5470 - X Color Inkjet

Бренд: Lexmark Страницы: 202

DocuColor 45087638

Бренд: Xerox Страницы: 28

Бренд: Sagem Страницы: 154

Automatic Photo Book Station

Бренд: Durst Страницы: 2

PRINTELLIGENSE ML-2245

Бренд: Samsung Страницы: 2

Office Master SCX-5312F

Бренд: Samsung Страницы: 127

SCX 4500 - B/W Laser - All-in-One

Бренд: Samsung Страницы: 172

Office Master SCX-5312F

Бренд: Samsung Страницы: 180

ProXpress C267x series

Бренд: Samsung Страницы: 349

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды