Frymaster FilterQuick 5FQG30U Скачать руководство пользователя страница 44

Страница: 44 / 54

6-4

6.2.3 Basket Lift Problems

PROBLEM

PROBABLE CAUSES

CORRECTIVE ACTION

Basket lift movement is

jerky and/or noisy.

Basket lift rods need lubrication.

Apply a light coating of Lubriplate

™

or similar

lightweight white grease to the rod and bushings.

6.2.4 Filtration

Problems

PROBLEM

PROBABLE CAUSES

CORRECTIVE ACTION

Fryer filters after each

cook cycle.

Filter prompt setting incorrect.

Change the filter prompt setting.

Filter menu functions

won’t start or

controller displays

WAIT FOR

Filter

Temperature too low or
controller displays OFF.

Another function is still in
process.

MIB has not cleared checking
system.

Messages or errors on other
controllers.

Filter pan not fully engaged.

Ensure fryer is at setpoint before starting;
ensure the controller is ON.

Wait until the previous function ends to start
another filtration cycle.

Wait one minute and try again.

Clear messages and errors on other controllers.

Ensure the filter pan is in position and fully
inserted into the fryer and “A” is displayed on
the MIB board.

Controller displays

FLT DYLD or

POL dlyd

Another function is in process or the
filter has been bypassed.

Wait until the previous function ends to start

another filtration cycle or select “YES” to “FILTER
NOW?” if present on another controller.

Filter pump won’t

start or pump stops

during filtering.

A. Power cord is not plugged in or

circuit breaker is tripped.

B. Pump motor has overheated

causing the thermal overload
switch to trip.

C. Blockage in filter pump.

A. Verify that the power cord is fully plugged in

and the circuit breaker is not tripped.

B. If the motor is too hot to touch for more than a

few seconds, the thermal overload switch has
probably tripped. Allow the motor to cool at
least 45 minutes then press the Pump Reset
Switch (see page 4-3).

C. Call your FAS for assistance.

Filter Pump runs, but

oil return is very slow.

Improperly installed or prepared
filter pan components or cold oil.

Remove the oil from the filter pan and
replace the filter paper, ensuring that the filter
screen is in place

under

the paper.

Verify that O-rings are present and in good
condition on filter pan connection fitting.

Controller displays

OIL IN DRAIN

PAN / CONFIRM

Drain valve open or possibility that
oil is in drain pan.

Press



(CONFIRM) and follow directions for

FILL VAT FROM DRAIN PAN.

Drain valve or return

valve stays open.

AIF board has failed.

B. Actuator has failed.

Call your FAS for assistance.

Controller displays

INSERT pan

Filter pan is not fully set into
fryer.

Missing filter pan magnet.

Defective filter pan switch.

Pull filter pan out and fully reinsert into fryer.

Ensure the filter pan magnet is in place and
replace if missing.

If the filter pan magnet is fully against the
switch and computer continues to display

INSERT pan

, switch is possibly defective.

Содержание FilterQuick 5FQG30U























































Результаты поиска

Содержание FilterQuick 5FQG30U

Отзывы:

Бренды по названию

Популярные бренды

Frymaster FilterQuick 5FQG30U, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание FilterQuick 5FQG30U

Отзывы:

Бренды по названию

Популярные бренды