Frymaster FilterQuick 5FQG30U Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 54

Frymaster FilterQuick 5FQG30U Скачать руководство пользователя страница 43

6-3

PROBLEM

PROBABLE CAUSES

CORRECTIVE ACTION

blower.

your FAS for service.

Controller displays

HEATING

FAILURE

.

Gas valve off, failed controller,
failed transformer, open high-limit
thermostat.

It is normal for this message to appear during
startup if the lines have air in them. Check that
the gas valve is on. If it continues, shut the fryer
down and call your FAS for assistance.

6.2.2 Error Messages and Display Problems

PROBLEM

PROBABLE CAUSES

CORRECTIVE ACTION

Controller displays

low temp

.

Frypot temperature has dropped
more than 30°F (17°C) lower than
setpoint in idle mode or 45°F (25°C)
in cook mode.

This display is normal for a short while if a large
batch of frozen product is added to the frypot or if
the fryer is not heating properly. If the issue
persists call your FAS for assistance.

Controller displays

Hot hi-1

.

Frypot temperature is more than
410ºF (210ºC) or, in CE countries,
395ºF (202ºC).

Shut the fryer down immediately and call your
FAS for assistance.

Controller displays

Hi

temp.

Frypot temperature is more than 40
ºF (4ºC).

Press the power button to turn off fryer and let
cool before returning power to fryer. If issue
continues call your FAS for assistance.

Controller displays

RECOVERY

FAULT/ YES

and

alarm sounds.

Recovery time exceeded maximum
time limit.

Clear error and silence the alarm by pressing the



(YES) button. Maximum recovery time is 2:25. If
the error continues call your FAS for assistance.

Controller display is in

wrong temperature scale

(Fahrenheit or Celsius).

Incorrect display option
programmed.

Fryers using the FilterQuick

™

controller can toggle

between F° to C° by pressing the



button until

Product setup is displayed. Press



to scroll to

Tech Mode and press



. Enter 1658. Press the

scan button. The controller displays

OFF

. Turn

the controller on to check temperature. If the
desired scale is not displayed, repeat.

Controller displays

High limit

failure

disconnect

power

.

A.

Open drain valve

B.

Failed high limit

A.

Close the drain valve.

B.

Shut the fryer down immediately and call your
FAS for assistance.

Controller displays

TEMP PROBE

FAILURE

Problem with the temperature
measuring circuitry including the
probe or damaged controller wiring
harness or connector.

Shut the fryer down and call your FAS for
assistance.

Controller displays

SERVICE

REQUIRED

followed

by an error message

.

An error has occurred which
requires a service technician.

Press the



(YES) button if the issue is fixed or

press the



(NO) button to continue cooking and

call your FAS for assistance. In some cases,
cooking may not be available.

«
...
41
42
43
44
45
...
»

Содержание FilterQuick 5FQG30U























































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды