Frymaster FilterQuick 5FQG30U Скачать руководство пользователя страница 17

Страница: 17 / 54

2-7

The FilterQuick™ FQG30 Series gas fryer has received the CE mark for the countries and gas
categories indicated in the table below.

NOTE:

The nominal heat input (QN) is 21kW except for

AT, DE, LU and category 3P/B, which is 23kW.

NOTICE- Australia Only

The air pressure switch on the combustion blower should read: Full Vat units-122pa
(0.5 inches W.C.) and for Split Vat units-180pa (0.72 inches W.C.).

COUNTRIES CATEGORIES

GAS

PRESSURE

(MBAR)

AUSTRIA (AT)

II2H3B/P

G20 20

G30, G31

BELGIUM (BE)

I2E(R)B

G20, G25

20, 25

I3+

G30, G31

28-30, 37

DENMARK (DK)

II2H3B/P

G20 20

G30, G31

FRANCE (FR)

G20, G25

20, 25

G30, G31

28-30, 37

II2Esi3P

G20, G25

20, 25

G31 50

FINLAND (FI)

II2H3B/P

G20 20

G30, G31

GERMANY (DE)

II2ELL3B/P

G20, G25

G30, G31

I3P G31

GREECE (GR)

II2H3+

G20 20

G30, G31

28-30, 37

ITALY (IT)

II2H3+

G20 20

G30, G31

28-30, 37

IRELAND (IE)

II2H3+

G20 20

G30, G31

28-30, 37

LUXEMBOURG (LU)

II2E3B/P

G20 20

G30, G31

NETHERLANDS (NL)

II2L3P

G25 25
G31 50

II2L3B/P

G25 25

G30, G31

NORWAY (NO)

I3B/P

G30, G31

PORTUGAL (PT)

II2H3+

G20 20

G30, G31

28-30, 37

SPAIN (ES)

II2H3+

G20 20

G30, G31

28-30, 37

II2H3P

G20 20
G31 37,

SWEDEN (SE)

II2H3B/P

G20 20

G30, G31

UNITED KINGDOM (UK)

II2H3+

G20 20

G30, G31

28-30, 37

CE Standard

Required airflow for the combustion air supply is 2m

/h per kW.

1. Connect the quick-disconnect hose to the fryer quick-disconnect under the fryer and to the

building gas line.

NOTE:

Some fryers are configured for a rigid connection to the gas supply line. These units

are connected to the gas supply line at the rear of the unit.

CE Approved Gas Categories by Country

Содержание FilterQuick 5FQG30U























































Результаты поиска

Содержание FilterQuick 5FQG30U

Отзывы:

Бренды по названию

Популярные бренды

Frymaster FilterQuick 5FQG30U, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание FilterQuick 5FQG30U

Отзывы:

Бренды по названию

Популярные бренды