Frymaster FilterQuick 5FQG30U Скачать руководство пользователя страница 42

Страница: 42 / 54

6-2

6.2

Troubleshooting Fryers

6.2.1 Controller and Heating Problems

PROBLEM

PROBABLE CAUSES

CORRECTIVE ACTION

No display on the

controller.

A. Controller not turned on.
B. No power to fryer.
C. Failed controller or other

component

A. Press the ON/OFF switch to turn the controller

on.

B. Verify that the fryer is plugged in and that the

circuit breaker is not tripped.

C. Call your FAS for assistance.

Controller displays

IS VAT FULL?

YES NO

during a

cook or in idle mode

with an audible

alarm.

An error has occurred due to
carbon buildup on oil level sensor.

CAN communication issues,
component failure issues.

If answering yes directs to IS OIL SENSOR
CLEAN? CONFIRM, clean the oil level
sensor with a scratch pad and power cycle the
controller.

If the issue persists contact your FAS for
assistance.

Controller displays

IS OIL SENSOR

CLEAM?

CONFIRM

during a

cook or in idle mode

with an audible

alarm.

The oil level sensor may be
coated with caramelized oil.

CAN communication issues,
component failure issues.

Clean sensor with scratch pad.

If the issue persists contact your FAS for
assistance.

Controller displays

CHANGE FILTER

PAPER?

Daily filter paper change prompt has
occurred.

Press



(YES), follow prompts and change the

filter paper.

Fryer repeatedly cycles

on and off when first

started.

Fryer is in melt cycle.

This is normal operation. This will continue until
the fryer temperature reaches 180ºF (82ºC).

Fryer does not heat.

A. Drain valve not fully closed.
B. Gas valve is not turned on.
C. Manual gas shut off valve closed.
D. Improperly connected quick-

disconnect fitting on gas line.

E. Obstructed or failed combustion air

blower.

Check status of MIB – Ensure

is displayed.

B. Turn the gas valve knob to the

position.

C. Verify that any in-line manual shut off and gas

main valve is open.

D. Verify that the quick-disconnect fitting on

the flexible gas line is firmly connected to the
fryer.

E. Verify that combustion air blower is running.

If not, call your FAS for service. If
combustion air blower is functional, clean and
adjust per instructions in Chapter 5 of this
manual.

Fryer is operating

normally, but recovery

is slow when cooking.

Dirty or obstructed combustion air
blower.

Clean and adjust per instructions in Chapter 5 of
this manual.

Heat indicator is on and

blower is running, but

burner will not ignite.

Blown fuse on interface board or
ignition module.

Contact your FAS for service.

Fryer is operating

normally, but produces

a popping sound when

burners ignite.

Dirty or obstructed combustion
air blower.

Dirty or obstructed gas valve vent
tube (non-CE fryers only).

Malfunctioning combustion air

Clean and adjust per instructions in Chapter 5
of this manual.

Clean per instructions in Chapter 5 of this
manual.

If blower is slow to come up to speed, contact

Содержание FilterQuick 5FQG30U























































Результаты поиска

Содержание FilterQuick 5FQG30U

Отзывы:

Похожие инструкции для FilterQuick 5FQG30U

Бренды по названию

Популярные бренды

Frymaster FilterQuick 5FQG30U, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание FilterQuick 5FQG30U

Отзывы:

Похожие инструкции для FilterQuick 5FQG30U

Бренды по названию

Популярные бренды