manualshive.com logo in svg

Frymaster FilterQuick 5FQG30U, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Frymaster FilterQuick 5FQG30U Скачать руководство пользователя страница 23

3-2 

3.1 

Controller Operation and Programming 

 

This fryer is equipped with the FilterQuick™ controller (illustrated below). Fryers with FilterQuick™ 
controllers should refer to the 

FilterQuick™ Controller Manual 819-7206 

for the controller program-

ming and operating procedure.  

 

 

    

                                     

FILTERQUICK™ CONTROLLER 

 

Refer to Chapter 4 of this manual for operating instructions for the built-in filtration system. 

 

3.2 

Equipment Setup and Start-Up Procedures 

 WARNING 

The on-site supervisor is responsible for ensuring that operators are made aware of 
the inherent hazards of operating a hot oil filtering system, particularly the aspects 
of oil filtration, draining and cleaning procedures. 

 

 

CAUTION 

The cooking oil capacity of the FilterQuick™ FQG30 Series gas fryer is 32 lbs. (3.8 
gallons/14.5 liters) at 70°F (21°C) for a full-vat and 18 lbs. (2.2 gallons/8.33 liters) at 
70°F (21°C) for each half of a dual-vat. 

 

Before lighting the fryer, make sure the fryer is OFF and the frypot drain valve(s) 
is/are closed.  Remove the basket support rack(s), if installed, and fill the frypot to 
the bottom OIL-LEVEL line. 

 

 
3.2.1 Setup 

 

 WARNING 

Never operate this appliance with an empty frypot.  The frypot must be filled with wa-
ter or oil before lighting the burners.  Failure to do so will damage the frypot and may 
cause a fire.

 

 

 DANGER 

Remove all drops of water from the frypot before filling with oil.  Failure to do so will 
cause spattering of hot liquid when the oil is heated to cooking temperature.

 

 

Содержание FilterQuick 5FQG30U























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды