Fritsch PULVERISETTE 5 Скачать руководство пользователя страница 58

Страница: 58 / 72

Repairs

DANGER!
Mains voltage!
– Before beginning with repair work, unplug the

mains plug and protect the device against being

unintentionally switched back on.

– Indicate repair work with warning signs.
– Repair work may only be performed by specialised

personnel.

– Put safety equipment back into operation after

maintenance work.

10.1 Checklist for troubleshooting

Fault description

Cause

Remedy

The POWER SUPPLY ready

status indicator doesn't light

No mains connection

Plug in mains plug.

Main switch (10) at 0 (OFF)

Switch on main switch.

Excess current protection switch

has been triggered

Press the excess current protection switch (9) on

the back of the device.

"START" button is pressed but

mill does not start up

POWER SUPPLY does not light up see above

Pause time active

Wait for end of pause or press "STOP".

Safety lock was opened man-

ually

Reactivate the safety lock, see

Chapter 2.6

„Protective equipment“ on page 14

Mill reduces speed automati-

cally

If REDUCED SPEED is lit: Over-

load

Reduce load or accept automatically set speed.

Mill stops running

Switched off due to thermal

overload of the drive

Allow device to cool down and select a lower

speed.

Imbalance of machine too high

Improve mass balance. (See

Chapter 6.6

„Mass balance“ on page 39).

Imbalance check has been trig-

gered.

Check grinding bowl weight; adjust imbalance

check sensitivity (see Chapter

Chapter 4.6.1

„Setting the imbalance check“ on page 24)

Drive was blocked

Rectify malfunction in grinding chamber.

Motor's V-belt loose or ripped

Check V-belt, replace if necessary.

Speed sensor is defective

Contact customer service.

The hood cannot be opened.

The hood handle (1) was not

properly operated during

opening.

Unlock the hood handle by pressing!

Repairs

- 58 -

Содержание PULVERISETTE 5









































































Результаты поиска

Содержание PULVERISETTE 5

Отзывы:

Похожие инструкции для PULVERISETTE 5

Бренды по названию

Популярные бренды

Fritsch PULVERISETTE 5, Руководство по эксплуатации

Результаты поиска

Содержание PULVERISETTE 5

Отзывы:

Похожие инструкции для PULVERISETTE 5

Бренды по названию

Популярные бренды