Fritsch PULVERISETTE 5 Скачать руководство пользователя страница 56

Страница: 56 / 72

Maintenance

DANGER!
Mains voltage
– Before beginning with maintenance work, unplug

the mains plug and protect the device against being

unintentionally switched back on again!

– Indicate maintenance work with warning signs.
– Maintenance work may only be performed by spe-

cialised personnel.

– Put safety equipment back into operation after

maintenance or repair work

NOTICE!
Send all Safe-Lock clamping systems to Fritsch GmbH

once a year for inspection. The customer must bear the

costs of this maintenance itself.

We recommend keeping a safety logbook

Chapter 15

„Safety logbook“ on page 67, where all work (mainte‐

nance, repairs......) performed on the device is entered.

The most important element of maintenance is regular

cleaning:

Functional part

Task or description

Test

Maintenance interval

Safety lock

Hood lock (7)

Is the closed hood (3)

locked in place when the

main switch is off?
If this test is failed, do not

continue to work until the

fault has been rectified.

Before each use

Rotating bearings

Permanent lubrication

Bearing clearance

Every 2,000 h or annually

Drive motor

Permanent lubrication

Bearing clearance

Every 4,000 h or annually

Maintenance

- 56 -

Содержание PULVERISETTE 5









































































Результаты поиска

Содержание PULVERISETTE 5

Отзывы:

Бренды по названию

Популярные бренды

Fritsch PULVERISETTE 5, Руководство по эксплуатации

Результаты поиска

Содержание PULVERISETTE 5

Отзывы:

Бренды по названию

Популярные бренды