Fritsch PULVERISETTE 5 Скачать руководство пользователя страница 13

Страница: 13 / 72

2.5 Device safety information

Only use original accessories and original spare parts. Failure to

observe this instruction can compromise the safety of the machine.

Safe conduct must be strictly observed during all work.

All currently applicable national and international accident preven-

tion guidelines must be complied with.

CAUTION!
Wear hearing protection!
If a noise level of 85 dB(A) is reached or exceeded, ear

protection should be worn to prevent hearing damage.

WARNING!
The maximum accepted concentration (MAC) levels of

the relevant safety guidelines must be observed; if nec-

essary, ventilation must be provided or the machine

must be operated under an extractor hood.

DANGER!
Explosion hazard!
– When Grinding oxidisable substances, e.g. metal or

coal, there is a risk of spontaneous combustion

(dust explosion) if the proportion of fine particles

exceeds a certain percentage. When Grinding these

kinds of substances, special safety measures must

be taken and the work must be supervised by a

specialist.

– The device is not explosion-protected and is not

suitable for Grinding explosive materials.

Do not remove the information signs.

NOTICE!
Immediately replace damaged or illegible information

signs.

Unauthorised alteration of the device will void Fritsch's declaration

of conformity to European directives and void the guarantee.

The PULVERISETTE 5 should only be used when it is in proper

working order, as intended and in a safety- and hazard-conscious

manner adhering to the operating manual. In particular, immediately

rectify any malfunctions that could pose a safety hazard.

If, after reading the operating manual, there are still questions or

problems, please do not hesitate to contact our specialised per-

sonnel.

Please observe!

Safety information and use

- 13 -

Содержание PULVERISETTE 5









































































Результаты поиска

Содержание PULVERISETTE 5

Отзывы:

Бренды по названию

Популярные бренды

Fritsch PULVERISETTE 5, Руководство по эксплуатации

Результаты поиска

Содержание PULVERISETTE 5

Отзывы:

Бренды по названию

Популярные бренды