Fritsch PULVERISETTE 5 Скачать руководство пользователя страница 25

Страница: 25 / 72

NOTICE!
The display above the right "–" button (x) in the

TIMER field is set to 9 by default. This indicates

that the imbalance check has been preconfigured

to the highest sensitivity level, preventing the

device from shifting position and any resulting

damage to the device. "1" indicates low sensi-

tivity and with "9" only slight imbalance is

required and the machine shuts down.
When the imbalance check is deactivated, a "0"

will be displayed in the TIMER field over the right

"–" button (x)!

To save and exit setup mode, press the STOP button.

After starting up (see Chapter

Chapter 5 „Initial start‐

up“ on page 27) begin grinding with 2 (4) bowls of the

same weight. If the machine stops and the error code

"UnbA" is displayed, press STOP and change the value

for the imbalance check from 9 to 8 in setup mode.

Repeat this process until your grinding is performed

with the parameters you require.

4.6.2 Setting time units

When the device has been switched off, press and hold the STOP

button on the front control panel.

Switch on the device with the main switch (10) on the back of the

device. There is a brief display check. After about 3 seconds setup

mode is started and the STOP button can be released.

If POWER SUPPLY is flashing, the device is in setup mode. If

POWER SUPPLY is not flashing, repeat the procedure.

Installation

- 25 -

Содержание PULVERISETTE 5









































































Результаты поиска

Содержание PULVERISETTE 5

Отзывы:

Бренды по названию

Популярные бренды

Fritsch PULVERISETTE 5, Руководство по эксплуатации

Результаты поиска

Содержание PULVERISETTE 5

Отзывы:

Бренды по названию

Популярные бренды