manualshive.com logo in svg

Fritsch PULVERISETTE 5, Руководство по эксплуатации

Поделиться
Скачать
Fritsch PULVERISETTE 5 Скачать руководство пользователя страница 41

6.8  Settings on the control panel

6.8.1  Setting the speed

n

Switch on the main switch (10) on the back of the device (I).

n

The green POWER SUPPLY ready status indicator lights up on the

control panel.

ROTATIONAL SPEED control panel area
Press and hold the + or - button.
The speed can be selected in steps of 10 between 50 and 400 1/min.
The actual speed is displayed during operation. The nominal speed is

briefly displayed when the + or - button is pressed.

6.8.2  Setting the running time

TIMER control panel area
Setting the grinding time
1.

Press the "MILLING" button.

ð

The "MILLING" button lights up

2.

Press the + or - buttons to set the running time in hours (0–99) and

minutes (0–59) or in minutes (0–59 and seconds (0–59).

Set the pause time
1.

Press the "PAUSE" button.

ð

The "PAUSE" button lights up.

2.

Press the + or - buttons to set the pause time in hours (0–99) and

minutes (0–59) or in minutes (0–59 and seconds (0–59).
If no pause time is required, set the pause time to 0.

 

Using the device

 

 

- 41 -

 

Содержание PULVERISETTE 5









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды