Fritsch ANALYSETTE 28 IMAGESIZER Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 62

background image

24

Installation

1

Connection, measuring unit

2

Outlet

3

Connection for external pump

4

Inlet for liquids (max. 0.5 bar)

5

Connection for measuring unit (only if the ultrasonic box is used)

6

Mains connection socket (only if the ultrasonic box is used)

1.

Connect the supplied data cable to the "Measuring Unit" connection (1) of

the dispersion unit and to one of the "Dispersion Units" connections of the

measuring unit.

2.

Connect the supplied outlet hose with inner diameter of 25 mm to the

outlet connector (2) and secure with the hose clamp included.

3.

Connect the wet dispersion unit with your building

connection; use the pressure regulator included. The

pressure regulator is equipped with an additional flow

limiter and thus reduces the pressure to 0.5 bar!

The "Inlet for liquids" connection (4) is used to fill the system with max. 0.5

bar. Connection the hose for the liquid to your building connection or liquid

storage tank and to the connection (4) on the dispersion unit. Secure the

hose with the hose clamps included.

«
...
22
23
24
25
26
...
»

Содержание ANALYSETTE 28 IMAGESIZER































































Отзывы:

Нет отзывов

Похожие инструкции для ANALYSETTE 28 IMAGESIZER

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

Бренд: Raith Страницы: 26

Бренд: Kane Страницы: 16

Бренд: Farmi Forest Corporation Страницы: 32

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Hanil Страницы: 24

Бренд: Hanil Страницы: 32

Бренд: Hanil Страницы: 24

Бренд: tayco Страницы: 111

Бренд: Teac Страницы: 9

Бренд: Tascam Страницы: 3

Бренд: Tascam Страницы: 56

Portastudio 2488

Бренд: Tascam Страницы: 28

Бренд: Tascam Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды