Frigidaire FFH17F7HWC Скачать руководство пользователя

Страница: 16 / 44

CONNECTING THE WATER SUPPLY

WARNING

To avoid electric shock, which can cause

death or severe personal injury, disconnect

the refrigerator from electrical power before

connecting a water supply line to the

refrigerator.



NOTE

Check with your local building authority

for recommendations on water lines and

associated materials prior to installing your

new refrigerator. Depending on your local/

state building codes, Frigidaire recommends

for homes with existing valves its

Smart

Choice

water line kit 5305513409 (with

a 6 ft. Stainless Steel Water Line) and for

homes without an existing valve, Frigidaire

recommends its

Smart Choice

water line

kit 5305510264 (with a 20 ft. Copper Water

Line with self-tapping saddle valve). Please

refer to www.frigidaire.com/store for more

information.

CAUTION

To Avoid Property Damage:
• Copper or Stainless Steel braided tubing

is recommended for the water supply

line. Water supply tubing made of ¼

inch plastic is not recommended to be

used. lastic tubing greatly increases

the potential for water leaks, and the

manufacturer will not be responsible for

any damage if plastic tubing is used for

the supply line.

• DO NOT install water supply tubing in

areas where temperatures fall below

freezing.

• Chemicals from a malfunctioning water

softener can damage the ice maker. If

your home has a water softening system,

ensure the softener is maintained and

working properly.

IMPORTANT

Ensure that your water supply line

connections comply with all local plumbing

codes.

Before Installing The Water

Supply Line, You Will Need:

•

Basic Tools: adjustable wrench, flat-blade

screwdriver, and Phillips

screwdriver

• Access to a household cold water line with

water pressure between 30 and 100 psi.

• A water supply line made of ¼ inch

(6.4 mm) OD, copper or stainless steel

tubing. To determine the length of tubing

needed, measure the distance from the

ice maker inlet valve at the back of the

refrigerator to your cold water pipe. Then

add approximately 7 feet (2.1 meters),

so the refrigerator can be moved out for

cleaning (as shown).

• A shutoff valve to connect the water supply

line to your household water system. DO

NOT use a self-piercing type shutoff valve.

•

Do not re-use compression fitting or use

thread seal tape.

• A compression nut and ferrule (sleeve) for

connecting a copper water supply line to

the ice maker inlet valve.

Содержание FFH17F7HWC













































Результаты поиска

Содержание FFH17F7HWC

Отзывы:

Похожие инструкции для FFH17F7HWC

Бренды по названию

Популярные бренды

Frigidaire FFH17F7HWC, Инструкция по использованию и уходу

Результаты поиска

Содержание FFH17F7HWC

Отзывы:

Похожие инструкции для FFH17F7HWC

Бренды по названию

Популярные бренды