Frigidaire FFH17F7HWC Скачать руководство пользователя

Страница: 39 / 44



NOTE

LED lights are in series so if one is bad or

unplugged, several lights may not light up.

CAUTION

Wear gloves when replacing incandescent

light bulbs to avoid getting cut.

CARE & CLEANING

Replacing LED Lights

(select

models)

The fresh food compartments of your

refrigerator may have LED lights. Always use

Frigidaire parts for replacement.

To replace LED Lights:

  1  Unplug your refrigerator’s power cord.
  2  Remove lens cover.
  3  Remove LED board.
  4  Replace LED board and snap in place

assuring the light is facing in toward the

unit (inside fresh food).

5 Replace lens cover.

Ordering Replacement LED Lights

Order new LEDs by calling 877-808-4195,

online at www.frigidaire.com/store, or through

the dealer where you bought the refrigerator.

Here is the product number to request when

ordering:

LED Light, Part #242196201

Incandescent Lights (40-watt bulb),

Part #5305514148

LED Light Board Removal

Lens Removal

Replacing Light Bulbs

(select models)

Light

Bulb

Light Sockets

Located Behind

Glass Shelves

Light

Bulb

Refigerator

Light Cover

Refrigerator Light

Light Socket

Located in Upper

Freezer Section

Freezer

Light Cover

Light

Bulb

Light

Bulb

Freezer Light

  1  Unplug your refrigerator’s power cord.
  2  Wear protective gloves.
  3  Remove light cover, if necessary.
  4  Unscrew and replace old bulb with an

appliance bulb of the same type and

wattage (normally 40 watts).

5 Replace light cover, if necessary.
6 Plug in the refrigerator’s power cord.

Содержание FFH17F7HWC













































Результаты поиска

Содержание FFH17F7HWC

Отзывы:

Похожие инструкции для FFH17F7HWC

Бренды по названию

Популярные бренды

Frigidaire FFH17F7HWC, Инструкция по использованию и уходу

Результаты поиска

Содержание FFH17F7HWC

Отзывы:

Похожие инструкции для FFH17F7HWC

Бренды по названию

Популярные бренды