Frigidaire FFH17F7HWC Скачать руководство пользователя

Страница: 17 / 44

IMPORTANT

Your refrigerator’s water supply system

includes several tubing lines, a water filter,

and a water valve. To ensure that your

water dispenser works properly, this system

must be completely filled with water when

your refrigerator is first connected to the

household water supply line.

CONNECTING THE WATER SUPPLY

Figure 1

Steel

Clamp

Brass

Compression

Nut

Water Line

Water Valve

Bracket

Valve Inlet

Water Valve

Water line from household

water supply

(Include enough tubing in loop to allow

moving refrigerator out for cleaning.)

Ferrule

(Sleeve)

Plastic Water Tubing

to Ice Maker

Fill Tube

To Connect Water Supply Line To

Ice Maker Inlet Valve

1 Disconnect refrigerator from electric power

source.

2 Place end of water supply line into sink or

bucket. Turn ON water supply and flush

supply line until water is clear. Turn OFF

water supply at shutoff valve.

3 Remove plastic cap from water valve inlet

and discard cap.

4 If you use copper tubing - Slide brass

compression nut, then ferrule (sleeve)

onto water supply line. Push water supply

line into water valve inlet as far as it

will go (¼ inch/6.4 mm). Slide ferrule

(sleeve) into valve inlet and finger tighten

compression nut onto valve. Tighten

another half turn with a wrench; DO NOT

over tighten. See Figure 1.

If you use stainless steel tubing - The

nut and ferrule are already assembled on

the tubing. Slide compression nut onto

valve inlet and finger tighten compression

nut onto valve. Tighten another half turn

with a wrench; DO NOT over tighten. See

Figure 1.

5 With steel clamp and screw, secure water

supply line (copper tubing only) to rear

panel of refrigerator as shown.

6 Coil excess water supply line (copper

tubing only), about 2½ turns, behind

refrigerator as shown and arrange coils so

they do not vibrate or wear against any

other surface. Do not kink tubing.

7 Turn ON water supply at shutoff valve and

tighten any connections that leak.

8 Reconnect refrigerator to electrical power

source.

9 To turn ice maker on, lower wire signal

arm (freezer ice maker) or set the ice

maker’s On/Off power switch to the “On”

position (fresh food ice maker).



NOTE

These instructions do not cover after market

ice maker installation. Instructions in after

market ice maker kit should be used.

Содержание FFH17F7HWC













































Результаты поиска

Содержание FFH17F7HWC

Отзывы:

Похожие инструкции для FFH17F7HWC

Бренды по названию

Популярные бренды

Frigidaire FFH17F7HWC, Инструкция по использованию и уходу

Результаты поиска

Содержание FFH17F7HWC

Отзывы:

Похожие инструкции для FFH17F7HWC

Бренды по названию

Популярные бренды