Frigidaire FFH17F7HWC Скачать руководство пользователя

Страница: 15 / 44

INSTALLING DOOR HANDLES

CAUTION

Wear gloves and safety goggles. Use extreme CAUTION when installing these handles.

Door Handle Mounting

Instructions for

Frigidaire Professional

Remove handles from carton and

any other protective packaging.

Position fresh food handle end

over upper and lower pre-

installed shoulder bolts (A) that

are fastened into door, ensuring

the holes for the set screws are

facing towards the opposite door.

While holding handle firmly

against door, fasten further

most upper and further most

lower Allen set screws (B) with

supplied Allen wrench.

Repeat steps 2 and 3 to install

opposite handle. Ensure the

holes for the set screws are

facing towards the first door.

Firmly tighten the inside Allen

set screws.

Position freezer handle end

over left and right pre-installed

handle mounts that are

fastened to the door, ensuring

the holes for the set screws

are facing down.

While holding handle firmly

against door, loosely tighten

far right Allen set screw (B)

with supplied Allen wrench

until there is no gap between

handle and door.

Still holding the handle firmly

to the door, firmly tighten far

left Allen set screw (B) with

supplied Allen wrench.

Return to the far right Allen set

screw (B) and firmly tighten

with supplied Allen wrench.

Firmly tighten the inside Allen

set screws.



NOTE

All set screws should be tightened so the screw is below the surface of the handle. The

handles should be drawn tight to freezer and refrigerator doors with no gaps. Opening the

opposite door while tightening the Allen screw makes installation easier.
The door handle may loosen over time or if it was installed improperly. If this happens,

tighten the set screws on the handles.

Mounting Refrigerator Handles

Mounting Freezer Handle

Содержание FFH17F7HWC













































Результаты поиска

Содержание FFH17F7HWC

Отзывы:

Похожие инструкции для FFH17F7HWC

Бренды по названию

Популярные бренды

Frigidaire FFH17F7HWC, Инструкция по использованию и уходу

Результаты поиска

Содержание FFH17F7HWC

Отзывы:

Похожие инструкции для FFH17F7HWC

Бренды по названию

Популярные бренды