Frigidaire FFH17F7HWC Скачать руководство пользователя

Страница: 11 / 44

CAUTION

Drawer is heavy. Use caution when lifting.

DOOR REMOVAL INSTRUCTIONS

Removing Freezer Drawer

1 Open freezer drawer.
2 Remove drawer screws on right and left sides (two screws on each side).

3 Lift drawer up and out to remove.

Installing Freezer Drawer

1 With lower slides pulled out, hang drawer

onto slide brackets ensuring pins on each

side are fully inserted into slots on each side.

  6  Tighten four drawer screws.
  7  Recheck gasket seal.
  8  To install toe grille, open freezer drawer, lift toe

grille and fit into place. Toe grilles vary by model.

Grab

Drawer

at Center

from Both

Sides

Then

Pull

Drawer

Out

Push

Against

Freezer

Drawer

Assembly

Slot

Cabinet

Fully Extend

Drawer Slides

Install

crews

(2) Each

Side

3 Check gasket seal around top, bottom,

and sides of freezer drawer.

4 If gasket is not sealed, open drawer and

slightly loosen four drawer screws (two on

each side) to allow drawer to rotate.

5 Close drawer and recheck the seal on the

gasket (A). Open the drawer grabbing by

the sides in the center (B). Be careful not

to rotate the drawer.



NOTE

Do not remove center screw from freezer
drawer. This is a factory adjustment.

2 Reinstall four drawer screws (two per

side), tighten down, and close drawer.

Loosen Hex Head

Drawer Screw

Loosen Hex

Head Drawer

Screw

Do Not Remove

Other Screws

Loosen Hex Head

Drawer Screw

Loosen Hex

Head Drawer

Screw

Содержание FFH17F7HWC













































Результаты поиска

Содержание FFH17F7HWC

Отзывы:

Похожие инструкции для FFH17F7HWC

Бренды по названию

Популярные бренды

Frigidaire FFH17F7HWC, Инструкция по использованию и уходу

Результаты поиска

Содержание FFH17F7HWC

Отзывы:

Похожие инструкции для FFH17F7HWC

Бренды по названию

Популярные бренды