manualshive.com logo in svg

Freescale Semiconductor MPC8250, Справочное руководство для семьи

Микросхема Freescale Semiconductor MPC8250 - это высокопроизводительное устройство, предназначенное для работы в различных электронных устройствах. Пользователи могут бесплатно скачать руководство по эксплуатации "Family Reference Manual" на manualshive.com. Это незаменимый инструмент для понимания функциональности и настроек данного продукта.

Поделиться
Скачать
background image

SDMA Channels and IDMA Emulation

MPC8260 PowerQUICC II Family Reference Manual, Rev. 2

19-10

Freescale Semiconductor

 

Any IDMA access to a peripheral uses the highest arbitration priority allowed for the DMA, providing 
faster bus access by bypassing other pending DMA requests.

19.5.2.1

Dual-Address Transfers

The following sections discuss various dual-address transfers.

19.5.2.1.1

Peripheral to Memory

Dual-address peripheral-to-memory data transfers are similar to memory-to-memory transfers using the 
three-phase algorithm; see 

Section 19.5.1, “Memory-to-Memory Transfers.”

 When a peripheral asserts 

DREQ, data is loaded from the peripheral in port-size units to the internal transfer buffer. When the transfer 
buffer reaches the steady-state level, it is automatically written to the memory destination in one transfer. 
The source transfer size (STS) is initialized to the peripheral port size, and the destination transfer size 
(DTS) is initialized to SS_MAX.

External requests must be enabled (DCM[ERM] = 1) for dual-address peripheral-to-memory transfers. If 
DONE is asserted externally by the peripheral or if a 

STOP

_

IDMA

 command is issued, the current transfer 

stops. All data in the internal transfer buffer is written to memory in one transfer before its BD is closed, 
and the IDSR[EDN] or IDSR[SC] event bits are set; see 

Section 19.8.4, “IDMA Event Register (IDSR) 

and Mask Register (IDMR).”

When the peripheral controls a transfer of unknown length, initialize a large enough buffer so that the 
peripheral will most likely assert DONE before overflowing the buffer. When DONE is asserted, the BD 
is closed and interrupts are generated (if enabled). The next DREQ assertion opens the next BD if 
DCM[DT] is set; see 

Section 19.8.2.1, “DMA Channel Mode (DCM).”

 

19.5.2.1.2

Memory to Peripheral

Dual-address memory-to-peripheral data transfers are similar to memory-to-memory transfers using the 
three-phase algorithm; see 

Section 19.5.1, “Memory-to-Memory Transfers.”

 STS is initialized to 

SS_MAX and DTS is initialized to the peripheral port size. The first DREQ peripheral assertion triggers 
a read of SS_MAX (or more in the first phase) bytes from the memory into the internal transfer buffer, 
automatically followed by a write of DTS bytes to the peripheral. Subsequent DREQ assertions trigger 
writes to the peripheral. When the transfer buffer has fewer than DTS bytes left, the next DREQ assertion 
triggers a read of SS_MAX bytes from memory, automatically followed by a write to the peripheral, and 
the sequence begins again. 

External requests must be enabled (DCM[ERM] = 1) for dual-address peripheral-to-memory transfers. If 
DONE is asserted externally by the peripheral or if a 

STOP

_

IDMA

 command is issued, the current transfer 

is stopped, its BD is closed, and the IDSR[EDN] or IDSR[SC] event bits are set; see 

Section 19.8.4, 

“IDMA Event Register (IDSR) and Mask Register (IDMR).”

19.5.2.2

Single Address (Fly-By) Transfers

When DCM[FB] = 1, both peripheral-to-memory and memory-to-peripheral transfers occur in fly-by 
mode; see 

Section 19.8.2.1, “DMA Channel Mode (DCM).”

 In fly-by mode, an internal transfer buffer is 

not needed because the data is transferred directly between memory and the peripheral. Also, parameters 

Содержание MPC8250

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC8250

3Com 3CRWEASY96A Quick Start Manual preview
3CRWEASY96A
Бренд: 3Com Страницы: 8
Harmonic XOS User Manual preview
XOS
Бренд: Harmonic Страницы: 56
Intel Optane M Series Installation And User Manual preview
Optane M Series
Бренд: Intel Страницы: 59
DAD DPX2060 User Manual preview
DPX2060
Бренд: DAD Страницы: 32
Orban OPTIMOD 6300 Operating Manual preview
OPTIMOD 6300
Бренд: Orban Страницы: 255
TDK HHM Series HHM2411 Specification Sheet preview
HHM Series HHM2411
Бренд: TDK Страницы: 2
AXIOMTEK AIE900-XNX Series User Manual preview
AIE900-XNX Series
Бренд: AXIOMTEK Страницы: 53
axing EOC 1-31 Operation Instructions Manual preview
EOC 1-31
Бренд: axing Страницы: 52
HighPoint SSD7540L Quick Installation Manual preview
SSD7540L
Бренд: HighPoint Страницы: 10
Idis DR-1204P Installation Manual preview
DR-1204P
Бренд: Idis Страницы: 22
AXIOMTEK CEM500 Quick Installation Manual preview
CEM500
Бренд: AXIOMTEK Страницы: 2
Xantech IR-X10 Installation Instructions Manual preview
IR-X10
Бренд: Xantech Страницы: 16
Intel CORE 2 DUO E4000 - 3-2008 Datasheet preview
CORE 2 DUO E4000 - 3-2008
Бренд: Intel Страницы: 122
Mod Duo X User Manual preview
Duo X
Бренд: Mod Страницы: 11
NuDAQ ACL-8112 Series User Manual preview
ACL-8112 Series
Бренд: NuDAQ Страницы: 92
Fibocom H330SS Hardware User Manual preview
H330SS
Бренд: Fibocom Страницы: 39
ICS Advent COMM4AT/EX Product Manual preview
COMM4AT/EX
Бренд: ICS Advent Страницы: 30
ABB COM600 series 5.1 User Manual preview
COM600 series 5.1
Бренд: ABB Страницы: 42

Бренды по названию

Популярные бренды

Загрузить еще бренды