Freescale Semiconductor MPC8250 Скачать руководство пользователя страница 1168

Страница: 1168 / 1360

Inverse Multiplexing for ATM (IMA)

MPC8260 PowerQUICC II Family Reference Manual, Rev. 2

33-66

Freescale Semiconductor

2. Assign corresponding group number for the new link: ILRCNTL[IGNUM] = x.

3. Assign channel number for ICP cell reception: RICPCH = x.

4. Enable desired interrupts: IRINTMSK = x

5. Allow for the reception of ICP cells during the IFSM stage: ILRCNTL[MON_ICP] = 1.

6. Indicate that this link has not yet been assigned to a group: ILRCNTL[GA] = 0.

7. Configure this link/PHY as an IMA link in the IMA Root Table by setting the corresponding bit in

IMAPHY. See

Table 33-3

8. Enable the corresponding link/PHY in the IMA Root Table by setting the corresponding bit in

RXPHYEN. See

Table 33-3

9. Software receives and accepts ICP cell values (e.g. M, LID, etc.).

10. Program expected LID: ILID = x

11. Program the expected ICP offset: LICPOS = x

12. Initialize the DCB pointers accordingly: DCBEP, DCBSP, DCBFP. Note, it is recommended that

the DCB be initialized to zero.

13. Configure link to “Loss of IMA Frame” state: ILRSTATE[FSES] = 2.

14. Start the IMA Frame Synchronization Mechanism (IFSM) by assigning this link to the group:

ILRCNTL[GA] = 1.

15. Software must now wait for the IFSW (IMA Frame Synchronization Working) event/exception.

16. Now that we have a “frame” synchronized link, we can proceed to allow the link to be “delay”

synchronized. Indicate that this is a new link (GDS/reconstruction function) by inverting the
current “add-new” bit value: ILRCNTL[ADD_NEW] = x.

17. Formulate new group order table with the new link included (see

Section 33.4.4.2.4, “Receive

Group Order Tables”

18. Use the new group order table by inverting the current GOTP value: IGRCNTL[GOTP] = x.

19. The “Stall Threshold” needs to be recalculated. This parameter defines the acceptable tolerance to

an emptied DCB condition (stalled link, see LS exception). The recommended new value is:
STALL_THR = 2 x RNUMLINKS x (3 + RX_FIFO). See

Section 33.4.4.2, “IMA Group Receive

Table Entry”

: IGRTE[STALL_THR] = x.

20. Start the delay compensation process for this link (in IMA Root Table) by setting the corresponding

bit in REF_LINK. See

Table 33-3

21. Software must now wait for the link delay synchronization process to complete. A LDS (Link

Delay Synchronized) exception will be generated by the PowerQUICC II as soon as this happens.

22. It is now safe for the link to receive data, set link to “active” mode: ILRCNTL[RXSC] = 1.

33.5.4.4.2

TX Parameters

1. Reset all TX parameters in the new link table entry to zero.

2. Assign corresponding group number for the new link: ILTCNTL[IGNUM] = x.

3. Enable desired interrupts: ITINTMSK = x.

4. Software formats content of ICP template accordingly (see section “Transmit ICP Cell

Signalling”).

«
...
1166
1167
1168
1169
1170
...
»

Содержание MPC8250

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MPC8250

Отзывы:

Бренды по названию

Популярные бренды

Freescale Semiconductor MPC8250, Справочное руководство для семьи

Результаты поиска

Содержание MPC8250

Отзывы:

Бренды по названию

Популярные бренды