Freescale Semiconductor MPC8250 Скачать руководство пользователя страница 651 | Manualshive

Страница: 651 / 1360

Freescale Semiconductor MPC8250 Скачать руководство пользователя страница 651

SDMA Channels and IDMA Emulation

MPC8260 PowerQUICC II Family Reference Manual, Rev. 2

Freescale Semiconductor

19-7

Figure 19-5

shows the IDMA transfer buffer.

Figure 19-5. IDMA Transfer Buffer in the Dual-Port RAM

Each buffer’s contents are transferred in three phases:

•

First phase. The internal transfer buffer is filled with [EOB

(alignment to source address)

+ SS_MAX]

bytes, read from the source bus. Then, if EOB

(alignment to destination address)

≤

EOB

(alignment to source

address)

, [EOB

(destination)

+ SS_MAX] bytes are written from the transfer buffer to the destination

bus; or if EOB

(destination)

> EOB

(source)

, [EOB

(destination)

+ (k-2)*32] bytes are written bytes are

written. This write transfer size leaves a remainder of 0–31 bytes in the transfer buffer after the last
write burst of the steady-state phase. After the first phase, burst alignment is ensured.

•

Steady-state phase. The transfer buffer is filled with SS_MAX bytes (k-1 bursts), read from the
source bus in STS units. Then, SS_MAX bytes are written to the destination bus, in DTS units,
from the transfer buffer. Because alignment is ensured from first phase, all bus transfers are bursts.
This sequence is repeated until there are no more than SS_MAX bytes to be transferred. A
remainder of 0–31 bytes is left in the transfer buffer after the last burst write.

•

Last phase. The remaining data is read into the transfer buffer in bursts, with the last 1–31 bytes
read in single accesses. All data in the transfer buffer is written to the destination bus in bursts, with
the last 1–31 bytes written in single accesses. The last transfers, read/write or both can be
accompanied with DONE assertion, if programmed.

Figure 19-6

shows an example of the three IDMA transfer stages.

SS_MAX

Initialized to (IDMA_transfer_buffer_size - 32) bytes, which is the steady-state maximum transfer size
of IDMA transfer. This condition ensures that the transfer buffer is either filled by one SS_MAX bytes
transfer and emptied in one or several transfers, or filled by one or several transfers to be emptied in
one SS_MAX bytes transfer. In terms of bursts, if the transfer buffer contains k bursts (each is 32 bytes
long), then SS_MAX equals to k-1 bursts which is (k-1)*32 bytes.

STS/DTS

Source/destination transfer size. These parameters determine the access sizes in which the
source/destination is accessed in steady state of work. At least one of these values (DTS/STS) must
be initialized to the value of SS_MAX.

Table 19-3. IDMA Transfer Parameters (continued)

Parameter

Description

SS_MAX

DMA_WRAP determines IDMA transfer buffer size

EOB[0–31]

32

64

96

0

128

(k-1)*32

(32 * k) bytes

Base Address (aligned to buffer size)

«
...
649
650
651
652
653
...
»

Содержание MPC8250

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды