Freescale Semiconductor MCF5329 Скачать руководство пользователя страница 905 | Manualshive

Страница: 905 / 924

Freescale Semiconductor MCF5329 Скачать руководство пользователя страница 905

Revision History

Freescale Semiconductor

B-3

SDRAM

Controller

Added step 3 to initialization/application section: “Configure the slew rate for the SDRAM external pins in the

GPIO module.”

Added note in memory map section pointing to the slew rate control register in the GPIO module.

Added Read Clock Recovery (RCR) Block section.

Updated SD_DQS signal descriptions.

Added note to SDCFG1[RD_LAT] field: “Note: The recommended values are just a starting point and may need
to be adjusted depending on the trace length for the data and DQS lines.”

FEC

Removed mention of MII_STATUS register in MII Management Frame Register register description section.

Max buffer size is 2047, not 2032. Changed throughout.

Reworded EMRBR[R_BUF_SIZE] description.

In Transmit Buffer Descriptor Field Definitions table, removed the last sentence from the data length field: “Bits

[15:5] are used by the DMA engine; bits[4:0] are ignored.” to avoid confusion.

USB Host

Corrected FRINDEX reset value from Undefined to 0x0000_0000.

Corrected address offsets for the following registers:

CAPLENGTH from 0x0100 to 0x0103
HCIVERION from 0x0102 to 0x0100

USB OTG

Changed USB_INTR[NAKE,ULPIE] from read-only to read/write in register figure.

Changed ID reset value from 0x0041_FA05 to 0x0042_FA05

Corrected address offsets for the following registers:

CAPLENGTH from 0x0100 to 0x0103
HCIVERION from 0x0102 to 0x0100
DCIVERSION from 0x0120 to 0x0122

Corrected cross-reference in USBCMD[ATDTW] field description.

Moved USBCMD[ATDTW] from bit location 12 to bit 14. Bit 12 is reserved.

Changed reset value of FRINDEX from undefined to 0x0000_0000

Changed OTGSC[1MSS] reset value from 0 to 1.

Added “This bit is self clearing,” to EPCRn[TXR] and EPCRn[RXR] bit descriptions.

Swapped bit encodings in EPCRn[RXI] bit description.

Changed Total Bytes field to span bits 30 – 16 instead of 29 – 16 in Endpoint Transfer Descriptor (dTD) figure.

Added note to dTD Token[Total Bytes] field.

Figure USB 2.0 Device States: moved “when the host resets...” arrow from Attach state to Default FS/HS state.

Added note in Interrupt/Bulk Endpoint Operation section, in third bullet under “RX-dTD is complete when:”

Added second note to Software Link Pointers section.

Added the following dTD Token[Total Bytes] field description: “For OUT transfers the total bytes must be evenly

divisible by the maximum packet length.”

Table B-1. MCF5329RM Rev 2 to Rev. 3 Changes (continued)

Chapter

Description

MCF5329 Reference Manual, Rev 3

«
...
903
904
905
906
907
...
»

Содержание MCF5329





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов