manualshive.com logo in svg

Freescale Semiconductor MCF5329, Справочное руководство, Страница: 286 / 924

Поделиться
Скачать
Freescale Semiconductor MCF5329 Скачать руководство пользователя страница 286

Interrupt Controller Modules

14-18

Freescale Semiconductor

explicitly disabled in the interrupt service routine. This design provides unique vector capability for all 
interrupt requests, regardless of the complexity of the peripheral device.

In some applications, it is expected that the hardware masking of interrupt levels by the interrupt controller 
is enabled. This masking capability can be used with the processor’s masking logic to form a dual-mask 
capability. In this operation mode, the IACK read cycle also causes the current interrupt level mask to be 
saved in the SLMASK register, and the new level being acknowledged loaded into the CLMASK register. 
This operation then automatically masks the new level (and all lower levels) while in the service routine. 
Generally, as the service routine completes execution, and the initiating request source has been negated, 
the saved mask level is restored into the current mask level to re-enable the lower priority levels.

Finally, the vector number returned during the IACK cycle provides the association with the request and 
the physical interrupt signal. The CLMASK and SLMASK registers are all loaded (if properly enabled) 
during the interrupt acknowledge read cycle.

14.3.2

Prioritization Between Interrupt Controllers

The interrupt controllers have a fixed priority, where INTC0 has the highest priority, and INTC1 has the 
lowest priority. If both interrupt controllers have active interrupts at the same level, then the INTC0 
interrupt ise serviced first. If INTC1 has an active interrupt with a higher level than the highest INTC0 
interrupt, the INTC1 interrupt is serviced first.

14.3.3

Low-Power Wake-up Operation

The system control module (SCM) contains an 8-bit low-power control register (LPCR) to control the 
low-power stop mode. This register must be explicitly programmed by software to enter low-power mode. 
It also contains a wake-up control register (WCR) sets the priority level of the interrupt necessary to bring 
the device out of the specified low-power mode. Refer to 

Chapter 8, “Power Management,”

 for definitions 

of the LPCR and WCR registers, as well as more information on low-power modes.

Each interrupt controller provides a special combinatorial logic path to provide a special wake-up signal 
to exit from the low-power stop mode. This special mode of operation works as follows:

1. The WCR register is programmed, setting the ENBWCR bit and the desired interrupt priority level.

2. At the appropriate time, the processor executes the privileged STOP instruction. After the 

processor has stopped execution, it asserts a specific processor status (PST) encoding. Issuing the 
STOP instruction when the WCR[ENBWCR] bit is set causes the SCM to enter the mode specified 
in LPCR[LPMD].

3. The entry into a low-power mode is processed by the low-power mode control logic, and the 

appropriate clocks (usually those related to the high-speed processor core) are disabled.

4. After entering the low-power mode, the interrupt controller enables a combinational logic path 

which evaluates any unmasked interrupt requests. The device waits for an event to generate a level 
7 interrupt request or an interrupt request with a priority level greater than the value programmed 
in WCR[PRILVL].

5. After an appropriately high interrupt request level arrives, the interrupt controller signals its 

presence, and the SCM responds by asserting the request to exit low-power mode.

MCF5329 Reference Manual, Rev 3

Содержание MCF5329





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов