manualshive.com logo in svg

Freescale Semiconductor MCF5329, Справочное руководство, Страница: 309 / 924

Поделиться
Скачать
Freescale Semiconductor MCF5329 Скачать руководство пользователя страница 309

Enhanced Direct Memory Access (eDMA)

Freescale Semiconductor

16-15

16.6.13 eDMA Interrupt Request Register (EDMA_INT)

The EDMA_INT provide a bit map for the16 channels signaling the presence of an interrupt request for 
each channel. Depending on the appropriate bit setting in the transfer-control descriptions, the eDMA 
engine generates an interrupt a data transfer completion. The outputs of this register are directly routed to 
the interrupt controller (INTC). During the interrupt-service routine associated with any given channel, it 
is the software’s responsibility to clear the appropriate bit, negating the interrupt request. Typically, a write 
to the EDMA_CINT in the interrupt service routine is used for this purpose.

The state of any given channel’s interrupt request is directly affected by writes to this register; it is also 
affected by writes to the EDMA_CINT. On writes to the EDMA_INT, a 1 in any bit position clears the 
corresponding channel’s interrupt request. A zero in any bit position has no affect on the corresponding 
channel’s current interrupt status. The EDMA_CINT is provided so the interrupt request for a single 
channel can easily be cleared without the need to perform a read-modify-write sequence to the 
EDMA_INT.

16.6.14 eDMA Error Register (EDMA_ERR)

The EDMA_ERR provide a bit map for the16 channels, signaling the presence of an error for each channel. 
The eDMA engine signals the occurrence of a error condition by setting the appropriate bit in this register. 
The outputs of this register are enabled by the contents of the EDMA_EEI,and then routed to the interrupt 
controller. During the execution of the interrupt-service routine associated with any DMA errors, it is 
software’s responsibility to clear the appropriate bit, negating the error-interrupt request. Typically, a write 
to the EDMA_CERR in the interrupt-service routine is used for this purpose. The normal DMA channel 
completion indicators (setting the transfer control descriptor DONE flag and the possible assertion of an 
interrupt request) are not affected when an error is detected.

The contents of this register can also be polled because a non-zero value indicates the presence of a channel 
error regardless of the state of the EDMA_EEI. The state of any given channel’s error indicators is affected 
by writes to this register; it is also affected by writes to the EDMA_CERR. On writes to the EDMA_ERR, 
a one in any bit position clears the corresponding channel’s error status. A zero in any bit position has no 
affect on the corresponding channel’s current error status. The EDMA_CERR is provided so the error 
indicator for a single channel can easily be cleared.

Address: 0xFC04_4026 (EDMA_INT)

Access: User read/write

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

R INT15 INT14 INT13 INT12 INT11 INT10 INT9

INT8

INT7

INT6

INT5

INT4

INT3

INT2

INT1

INT0

W

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 16-15. eDMA Interrupt Request Register (EDMA_INT)

Table 16-16. EDMA_INT Field Descriptions

Field

Description

15–0

INTn

eDMA interrupt request n
0 The interrupt request for channel n is cleared.
1 The interrupt request for channel n is active.

MCF5329 Reference Manual, Rev 3

Содержание MCF5329





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов