Freefly MoVI Скачать руководство пользователя

Страница: 26 / 30

SYMPTOM

POSSIBLE CAUSE

SOLUTION

MōVI Controller was not detected.

MōVI Controller did not allow binding.

Make sure the MōVI Controller is powered on and in range.

Turn off any other MōVI Controller that might be in range.

Use

Radio Config::Radio Action::Bind

to permit binding after

the Receiver Status LED changes to slow-flashing orange:

(See binding instructions in the Receiver section.)

Bind Failed.

Receiver Status LED:

(Slow-Flashing Red) OR

(Solid Red)

The input has been remapped in Tx Config.

Check the assignment of USER 1, USER 2, and USER 3 in the

Tx Config menu to see if the user input in question has been

remapped to one of these.

The input is broken/damaged.

Many user inputs can be remapped. For example, the Mode

Switch can be remapped to the USER 3 switch. See the Tx

Config menu section for more information.

A user input (e.g. Pan Speed Knob, Mode

Switch) is not working.

Pan/Tilt Speeds are at their minimum settings.

Increase these setting using the Speed Knobs.

The MōVI is in Majestic Mode.

Change to Dual Op. mode using the Mode Switch.

The Pan/Tilt Axes are not working.

Содержание MoVI































Результаты поиска

Содержание MoVI

Отзывы:

Похожие инструкции для MoVI

Бренды по названию

Популярные бренды

Freefly MoVI, Руководство пользователя

Результаты поиска

Содержание MoVI

Отзывы:

Похожие инструкции для MoVI

Бренды по названию

Популярные бренды