Freefly MoVI Скачать руководство пользователя | Manualshive

Страница: 27 / 30

background image

AUXILIARY TRANSMITTER:

The MōVI Controller Receiver can optionally be used as an Auxiliary Transmitter for controlling third-party wireless follow-focus systems. For more information on

supported systems, see the Follow-Focus Integration section. To change modes:

1

Auxiliary Transmitters and Auxiliary Data Port connector are sold separately.

Move the Receiver Channel Switch to the position indicated in the table below.

Hold down the FW Button and then press the Bind Button once.

The new mode will be active after the next power cycle.

1 -

2 -

3 -

MODE

CONNECTS TO

DESCRIPTION

MōVI Controller Receiver
Status LED:

(Solid Green)

MōVI Gimbal Controller, MōVI Data Port.
(See Receiver Installation section.)

MōVI Controller Auxiliary Data Port.

1

In this mode, the MōVI Controller Receiver
acts as an Auxiliary Transmitter for sending
commands to a Redrock Micro microRemote
Basestation.

This is the normal operating mode for
two-way communication from the MōVI
Controller to the MōVI. The Receiver that
comes included with the MōVI Controller
is in this mode by default.

MōVI Controller Auxiliary Data Port.

1

Set Channel: 0 - C
Press Bind Button while
holding down FW Button.

microRemote Auxiliary Transmitter
Status LED:

(Slow-flashing green/orange)

Set Channel: D
Press Bind Button while
holding down FW Button.

In this mode, the MōVI Controller Receiver
acts as an Auxiliary Transmitter for sending
commands to a Hocus Products Axis 1 Digital
Receiver.

Axis 1 Auxiliary Transmitter
Status LED:

(Fast-flashing green/orange)

Set Channel: E
Press Bind Button while
holding down FW Button.

«
...
25
26
27
28
29
...
»

Содержание MoVI































Отзывы:

Нет отзывов

Похожие инструкции для MoVI

Бренд: Canon Страницы: 14

IMAGE STABILIZER EF70-200MM F/4L IS USM

Бренд: Canon Страницы: 13

TIMER REMOTE CONTROLLER TC-80N3

Бренд: Canon Страницы: 3

TIMER REMOTE CONTROLLER TC-80N3

Бренд: Canon Страницы: 2

EF-S55-250mm f/4-5.6 IS II

Бренд: Canon Страницы: 7

Бренд: Ecco Страницы: 9

Бренд: Ecco Страницы: 9

Бренд: La Crosse Technology Страницы: 2

Бренд: La Crosse Technology Страницы: 2

Бренд: La Crosse Страницы: 2

Бренд: VDO Cyclecomputing Страницы: 21

Бренд: Panasonic Страницы: 120

Бренд: Whispbar Страницы: 15

Бренд: Kargo Master Страницы: 6

CombiCool CAB-40B

Бренд: Waeco Страницы: 136

Бренд: CASTLECREEK Страницы: 3

Бренд: Inateck Страницы: 8

Alarm Clock Camera Case

Бренд: Wasserstein Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды