manualshive.com logo in svg

Freefly MoVI, Руководство пользователя

Поделиться
Скачать
Freefly MoVI Скачать руководство пользователя страница 23

RADIO MODE

MōVI:

DSMX 2048:

By default, the MōVI Controller uses a proprietary bidirectional communication protocol. 

TETHER/RX FW:

In this mode, the MōVI Controller relays raw data between the Receiver and a host computer via USB. This can be used to control the MōVI from a computer 

interface, or to update the Receiver firmware.

To add compatibility with other systems, it can be configured to output a Spektrum DSMX 2048 satellite receiver signal via the 3-pin Spektrum connector on 

the MōVI Controller Receiver. The channel mapping in DSMX 2048 mode is shown below.

SPEKTRUM DSMX 2048 CHANNEL

MŌVI CONTROLLER FUNCTION

Aileron

Elevator

Pan

Tilt

Throttle

Rudder

Pan Speed

Roll Trim

Gear

Aux1

TK Rec Start/Stop

TK Mode Switch (Dual, Majestic, Kill)

Aux2

Tilt Speed

Configure the operation of wireless Focus-Iris-Zoom (FIZ) systems in this menu. For more information on supported systems, see the Follow-Focus Integration section.

FIZ CONFIG

SYSTEM

Choose between supported wireless follow-focus systems. See Follow-Focus Integration section for more details on supported systems. Choose 

None to disable the Auxiliary Transmitter and allow follow-focus control from a separate handset.

INPUT

Choose which user input axis is active on the Auxiliary Transmitter output. The Focus Knob, Zoom Rocker, and Iris Knob can each be optionally 

selected for output to a single-axis system. For direction reversal, see the Tx Config menu section above.

To save FIZ configuration settings, use 

Tx Config::Tx Action::Save

.

Содержание MoVI































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды