background image

 

FORTEZA JSC                                                                          FORTEZA FMC 24 Pro (100m, 200m, 300m) 

 
 

Please visit our internet sites:                        

www.forteza.com

    or    

www.forteza.eu

                   Page 9 

 

Transmitters control panel ( TX ) 

 

 

Fig. 1.5 

        

Markings (TX): 

1 – LED indication 
2 – Tamper circuit 
3 – Frequency band switch 1-8 
 

 
Note.  Dear user! The manufacturer of the detector constantly upgrades their quality and 
reliability.    That’s  why  in  some  lots  of  detectors  one  can  find  design  modifications 
unspecified  in  the  documents  delivered  with  the  detectors.  Nevertheless,  the  main 
specifications are valid. 

1.6. Adjustment, control and indication parts 

 

 

1.6.1. The micro channels switches provided the frequency channels switch are set on 

the transmitter and the receiver. Only one of four switches can be set with the same number 
on the receiving and the transmitting side when the power supply is ON.  
 

1.6.2.  Adjustment  and  control  of  the  sensors  is  performed  by  using  the  controller 

placed on the receivers panel,  using Android or Windows software. 
 

1.6.3.  Manual  adjustment:  adjustment  is  possible  without  software,  only  visually 

"from the eye". 

1.6.4.  Possibilities  when  using  Android  or  Windows  device:  visualization  of 

calibration; selection of the detection zone length; AUTOMATIC, MANUAL or SPECIAL 
sensitivity adjustment modes. 
 

1.6.5.  To  prevent  unauthorized  openings  of  the  cover  6  (fig.1.2),  a  tamper  button  is 

placed in the receiver. The tamper contacts are closed in the operating state. When the cover

 

Содержание FMC 24 Pro





































Отзывы: