FORTEZA FMC 24 Pro Скачать руководство пользователя страница 33

Страница: 33 / 36

FORTEZA JSC FORTEZA FMC 24 Pro (100m, 200m, 300m)

Please visit our internet sites:

www.forteza.com

www.forteza.eu

Page 33

Attention !
PC program Forteza Software Windows has implemented ability to perform a test in

order to check the environmental influence on the sensors protection zone and to
receive recommendations for selecting the levels of the thresholds, which are in use.

The sequence of actions when performing the test:

Perform sensor adjustment (orientation of the transmitter / receiver to each other)

Select levels of thresholds for intruder detection.

Activate the test

During the test:

-The intruder must not be in the detection zone.

-Simulate possible environmental influence on the detection zone (movement of

nearby transport or people, swaying of branches or bushes, due to the wind and etc.)

Duration of the test:

Minimum – 15 seconds

Maximum – until the activation of the software widow “Next”

Possible messages after the test procedure:

- Noise immunity is good – it means that the value of the interference level / threshold

level ratio is sufficient for the sensor to work stably.

-Noise immunity is bad – it means that the value of the interference level / threshold level

ratio is not sufficient for the sensor to work stably and is critical. The display shows the
recommended threshold levels for such interference.

-Very big interference – it means that the value of the interference level / threshold level

ratio is unacceptable. Sensors stable operation is not possible.

Содержание FMC 24 Pro





































Результаты поиска

Содержание FMC 24 Pro

Отзывы:

Похожие инструкции для FMC 24 Pro

Бренды по названию

Популярные бренды

FORTEZA FMC 24 Pro, Общее описание устройства

Результаты поиска

Содержание FMC 24 Pro

Отзывы:

Похожие инструкции для FMC 24 Pro

Бренды по названию

Популярные бренды