Ford TRANSIT CUSTOM 2012.75 страница 137 Скачать руководство пользователя | Manualshive

Страница: 137 / 184

background image

Description

Item

Left Hand Drive Switch options

A

Right Hand Drive Switch options

B

Beacon

1

Water Heater*

2

Aux 1 — Part of Utility Vehicle Switch Pack (A607)

3

Aux 2 — Part of Utility Vehicle Switch Pack (A607)

4

SVO Switches and Harness Part Numbers

Aux 2 (12V)

Aux 1 (12V)

Water Heater*

Beacon

Harness

-

-

-

BK2V-13768-A

BK2V-14A303-A

-

-

BK2V-19H218-A_

BK2V-13768-A

BK2V-14A303-B

BK2V-13D734-B_

BK2V-13D734-A_

-

BK2V-13768-A

BK2V-14A303-F

* Limited availability check with your Local Ford Dealer or National Sales Company representative.

There are a combination of switch packs available
to order for specific conversions. The 'Beacon
Preparation Pack' or 'Utility Vehicle Switch Pack'
are high current latched switches that control
relays in the Auxiliary Fuse Panel. When the
switches are pressed (light on) the switches
provide a +12V/20A output.

NOTE:

The Water Heater or Aux 2 switches must

have the engine running before they will give an
output. The output will be switched off during an
engine auto-off (Start-Stop vehicle). The other
switches (Beacons and Aux 1) are fed directly from
the battery. It is important to switch these off
when not required, as the battery charge level will
be depleted.

If heavy loads are required, controlled via these
switches (especially at engine off) it is
recommended to install the High Performance
Deep Cycle AGM battery option (A736). The
switches are illuminated red when the lights are
in: side, dipped, full beam or auto lights on. They
12V and can switch up to 8A directly.

Date of Publication: 04/2012

FORD

TRANSIT CUSTOM

2012.75

4 El

ec
tric

al

137

«
...
135
136
137
138
139
...
»

Содержание TRANSIT CUSTOM 2012.75

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TRANSIT CUSTOM 2012.75

Бренд: Vauxhall Страницы: 177

Бренд: Toyota Страницы: 56

Бренд: TATA Motors Страницы: 156

Бренд: Mazdaspeed Страницы: 8

Бренд: WABCO Страницы: 48

Бренд: Hyundai Страницы: 19

Бренд: Oldsmobile Страницы: 354

Бренд: Lexus Страницы: 34

Бренд: Toyota Страницы: 32

Бренд: ULTIMATE SPEED Страницы: 10

Бренд: POOL-LINE Страницы: 2

Бренд: Horn Tools Страницы: 12

Бренд: Calix Страницы: 4

Бренд: Reliant Страницы: 116

Бренд: Buick Страницы: 371

Бренд: Brodit Страницы: 2

Бренд: Magneti Marelli Страницы: 3

Бренд: Lexus Страницы: 878

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды