Ford TRANSIT CUSTOM 2012.75 страница 65 Скачать руководство пользователя | Manualshive

Страница: 65 / 184

background image

Tow bar electrical system may be ordered as a
13-pin DIN connector, as part of the original vehicle
build.

Where it is required to add trailer towing to an
existing vehicle, and to ensure compliance with
lighting regulations, the appropriate wiring
accessory kit can be obtained from your Ford
Dealer.

Fitment of non-Ford trailer tow wiring is not
advisable due to Body Control Module control of
lighting, and meeting legal lighting regulations.
Contact your local Ford dealer for details of a
harness that connects to the base vehicle harness.

NOTE:

For Van tow bars it is necessary to connect

into the rear lamp unit.

NOTE:

If tow bar connectors are not used,

appropriate fixing and cover must be applied for
protection from water and contaminant ingress.

NOTE:

The trailer detect circuit is part of the Ford

Trailer Tow module, it can only be implemented
on vehicles with power locking and perimeter or
CAT 1 alarms.

The Trailer Tow Module (TTM) can support pure
LED trailer lights as long as each circuit exceeds
500mA, below this and the system will not detect
a trailer has been connected and shuts down all
outputs (sleep mode). It is recommended to
target a 550mA mimimum load to allow for
system tolerances. This would need to be
obtained with a supplemental load resistor, if the
LED lighting circuits are below this threshold.

Each output driver could handle a current of 15A
but it is not recommended to always run to this
maximum. A higher current is interpreted as short
circuit. If a short circuit is detected the related
output will be switched off. The following table
shows the recommended output maximums per
circuit.

Trailer Tow Module Connectors (Figure E151247 and E145361)

Voltage (V)

Current (A)

Feature

Max

Min

Max

Min

Circuit Number

Component

Terminal

Number

Connector A

-

6

3

0.5

Right Direction Indicator

1

16

9

10

-

Battery Charge Out

2

-

6

4

0.5

Stop Left

3

-

-

-

-

Not used

4

-

-

-

-

Not used

5

-

6

4

0.5

Reverse Light

6

-

6

4

0.5

Stop Right

7

-

6

2

0.5

Fog Light

8

-

-

-

-

Not used

9

-

6

3

0.5

Left Direction Indicator

10

-

-

-

-

Not usedPin

11

-

6

7

0.5

Position Light

12

Connector B

-

-

-

-

Not used

1

16

6

30

-

Term 30 (Ubat)

2

Connector C

-

6

0.1

-

CAN H

1

-

6

0.1

-

CAN L

2

-

6

0.1

-

Brake Line In (Vehicle -)

3

-

6

1

-

Ground

4

16

-

0.1

-

Trailer Detect Output

5

Date of Publication: 04/2012

FORD

TRANSIT CUSTOM

2012.75

4 El

ec
tric

al

65

«
...
63
64
65
66
67
...
»

Содержание TRANSIT CUSTOM 2012.75

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TRANSIT CUSTOM 2012.75

Бренд: Federal Signal Corporation Страницы: 8

Бренд: Federal Signal Corporation Страницы: 8

BLADE-AL(TB)-TL2

Бренд: iDataLink Страницы: 9

Бренд: Magneti Marelli Страницы: 2

Бренд: Whispbar Страницы: 15

Бренд: ULTIMATE SPEED Страницы: 50

Бренд: Weltmann KFZ-Teile Страницы: 12

2917 Nstallation

Бренд: Edelbrock Страницы: 1

Бренд: Toyota Страницы: 497

Sprinter Bed System DIY

Бренд: FVC Страницы: 8

Бренд: Buick Страницы: 112

Бренд: Hyundai Страницы: 380

Бренд: NavLinkz Страницы: 26

Бренд: WABCO Страницы: 40

Бренд: Erich Jaeger Страницы: 16

SKT 170 HYUNDAI

Бренд: Paser Страницы: 4

Бренд: Yakima Страницы: 13

Бренд: Ferrari Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды