manualshive.com logo in svg

Ford TRANSIT CUSTOM 2012.75, Руководство по монтажу

Поделиться
Скачать
Ford TRANSIT CUSTOM 2012.75 Скачать руководство пользователя страница 5

5.6

Body Closures...................................161

5.6.1

Load Compartment Interior
Lining.............................................................161

5.6.2

Plywood Lining/Cladding......................161

5.6.3

Security, Anti Theft and Locking
System .........................................................161

5.7

Seats................................................166

5.7.1

Van................................................................166

5.7.2

Windowed Van.........................................166

5.7.3

Heated Seats.............................................166

5.7.4

Rear Seat Fixing Positions....................166

5.8

Glass, Frames and Mechanisms.....169

5.8.1

Heated Windshield and Heated Rear
Window.......................................................169

5.8.2

Rear Windows...........................................169

5.9

Roof Opening Panel..........................171

5.9.1

Roof Ventilation.........................................171

5.9.2

Roof Racks...................................................171

5.10 Airbag Supplemental Restraint

System (SRS)...................................173

5.10.1

Air Bags.........................................................173

5.11

Safety Belt System..........................176

5.11.1

Seat Belts....................................................176

5.11.2

Driver Belt-Minder....................................176

5.12 Corrosion Prevention.......................177

5.12.1

General.........................................................177

5.12.2 Repairing Damaged Paint......................177
5.12.3 Under Body Protection and

Material.........................................................177

5.12.4 Painting Road Wheels.............................177
5.12.5 Contact Corrosion.....................................177

5.13 Frame and Body Mounting..............178

5.13.1

Mounting Points and Tubing................178

5.13.2 Frame Drilling and Tube

Reinforcing..................................................178

5.13.3 Area for Fitting Additional Body

Attachments to the Rear of the
Bumper.........................................................179

5.13.4 Water Tank on Camper Vehicles........179

T

abl

e of C

ont

ents

5

Содержание TRANSIT CUSTOM 2012.75

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды