Ford TRANSIT CUSTOM 2012.75 страница 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 184

background image

1.9 Jacking

WARNING: Always position the vehicle
on a hard level surface. If the vehicle must
be jacked up on a soft surface use load
spreading blocks under the jack. Always
chock the wheel diagonally opposite the
jacking point. Failure to follow these
instructions may result in personal injury.

CAUTIONS:

It is important that only the correct
jacking and support locations are used at
all times.

Make sure that access to the spare wheel
is maintained when converting the vehicle
or relocating the spare wheel.

NOTE:

When using the vehicle jack, refer to the

owner guide for correct operating instructions.

NOTE:

Make sure that reinforcements are installed

to maintain the integrity of the original body
structure for/at jacking points.

NOTE:

Any modifications to the vehicle must be

noted in the owner's handbook or new descriptive
literature included with the owner's
documentation.

Front Jacking Points

Rear Jacking Points

FORD

TRANSIT CUSTOM

2012.75

Date of Publication: 04/2012

1 G

ener

al Inf

orma

tion

22

«
...
20
21
22
23
24
...
»

Содержание TRANSIT CUSTOM 2012.75

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TRANSIT CUSTOM 2012.75

Бренд: Daihatsu Страницы: 41

Бренд: Daihatsu Страницы: 268

Бренд: Jeep Страницы: 25

Бренд: Wagan Страницы: 12

Бренд: kincrome Страницы: 6

Бренд: Lexus Страницы: 369

Бренд: Mountain Top Страницы: 12

Бренд: Safe Fleet Страницы: 11

Бренд: Camec Страницы: 19

Escalade ESV 2014

Бренд: Cadillac Страницы: 508

Бренд: Hama Страницы: 2

Carpower CAP-20

Бренд: Monacor Страницы: 2

Бренд: Kuda Страницы: 3

2014 Grand Cherokee SRT8

Бренд: Jeep Страницы: 596

Бренд: Skoda Страницы: 4

Бренд: Skoda Страницы: 165

Бренд: Improved Racing Страницы: 17

Бренд: Mitsubishi Страницы: 367

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды