FMI (V)KC36NE series Скачать руководство пользователя страница 24

Страница: 24 / 40

www.fmiproducts.com

116238-01L

PRESSURE TESTING FIREPLACE GAS

CONNECTIONS

1. Open equipment shutoff valve (see Figure

33, page 23).

2. Open propane/LP supply tank valve for

propane/LP fireplace or main gas valve

located on or near gas meter for natural

gas fireplace.

3. Make sure control knob of fireplace is in

the OFF position.

4. Check all joints from equipment shutoff

valve to gas valve (see Figure 34 or 35

on page 23). Apply noncorrosive leak de

tection fluid to all joints. Bubbles forming

show a leak. Correct all leaks at once.

5. Light fireplace (see

Operation

, page 28).

Check all other internal joints for leaks.

6. Turn off fireplace (see

To Turn Off Gas to

Appliance

, page 28).

REMOVING/REPLACING GLASS

DOOR

FIREPLACE

INSTALLATION

Continued

Removing Louver Panels

Remove top and bottom louver panels by

simultaneously pulling both top end spring

latches towards center of appliance until

they are disengaged from locating holes

(see Figure 36). Repeat for bottom spring

latches and pull louvers outward. To install

or replace items removed, simply reverse

procedures above.

Figure 36 - Removing Louver Panel

Louver

Panel

Spring

Latch

Figure 37 - Removing/Replacing Screen

Door Assembly (KCC36 Series)

Magnetic Door Latches

(KCC36 Series)

Screen Door Tabs

(KCC36 Series)

Slots underneath

Upper Face

Removing Screen Door Assembly

(KCC36 Series)

Push screen door assembly in toward the bottom

left and right sides until the magnetic door latch

pops the screen door out. Hold the screen door

assembly at the bottom and swing the door up

to disengage the tabs on the top of the door from

inside the slots underneath the upper face.

Replacing Screen Door Assembly

(TCC36 Series)

Push magnetic door latch out to the open

position. Position screen door tabs with slot

openings in upper face frame. Swing door

screen assembly in towards the bottom face,

Press in on the bottom of door screen until

magnetic door latch is pushed in.

CAUTION: Do not operate

this fireplace with a broken glass

door panel or without the glass

door panel securely in place. For

replacement part information see

Replacement Parts

, page 34.

CAUTION: Wear gloves and

safety glasses while handling or

removing broken glass. Do not

remove if glass is hot. Keep chil

dren and pets away from glass.

WARNING: If fireplace has

been running, turn off and un

plug fireplace. Let cool before

removing glass door or louvers.

Содержание (V)KC36NE series









































Результаты поиска

Содержание (V)KC36NE series

Отзывы:

Похожие инструкции для (V)KC36NE series

Бренды по названию

Популярные бренды

FMI (V)KC36NE series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание (V)KC36NE series

Отзывы:

Похожие инструкции для (V)KC36NE series

Бренды по названию

Популярные бренды