FMI (V)KC36NE series Скачать руководство пользователя

Страница: 19 / 40

www.fmiproducts.com

116238-01L

FIREPLACE

INSTALLATION

CHECK GAS TYPE

Use proper gas type for the fireplace unit you

are installing. If you have conflicting gas types,

do not install fireplace. See retailer where you

purchased the fireplace for proper fireplace

according to your gas type or to purchase gas

conversion kit (see

Accessories

, page 35).

INSTALLING OPTIONAL BLOWER

ACCESSORIES

NOTICE: If installing blower in

an existing fireplace with gas

connections, shut off gas sup

ply and disconnect heater from

gas supply. Contact a qualified

service person to do this.

WARNING: If there is a duplex

electrical outlet installed in the

right side of the bottom of the

fireplace base area, be sure that

the electrical power to the outlet

is turned off before proceeding

with blower installation. Failure

to do this may result in serious

injury.

Model BK Installation

Follow all instructions provided in blower

accessory kit.
1. Attach power cord to blower motor by

firmly pushing two female terminals at end

of power cord onto two spade terminals

on blower motor (see Figure 25).

2. Attach green ground wire from power

cord to blower housing using screw pro

vided (see Figure 25). Tighten screws

securely.

3. Place blower against lower rear wall of

firebox outer wrapper with exhaust port

directed upward. Blower will fit inside back

opening and be held in position against

back wall by magnets (see Figure 25).

4. Be certain that all wire terminals are

securely attached to terminals on blower

motor and that screw retaining green

ground wire is tight.

Blower Location

Side View

Figure 25 - Blower Model BK

Magnetic

Strips

Exhaust Port

Screw

Green

Ground

Wire

Spade

Terminals

Lower Firebox

Cavity

5. Mount speed control box to switch bracket

by placing plastic control shaft forward

through round opening in switch bracket

(see Figure 26).

6. While supporting speed control, secure

control shaft with lock nut by pushing

and turning lock nut with pliers clockwise

until it is tight against front panel. Place

provided control knob on shaft.

7. Turn on power to duplex outlet if previously

turned off per warning in column 1.

8. Plug in blower power cord.

a. If your firebox is installed as a free

standing unit with an accessory mantel,

determine whether power cord will exit

left side or right side of firebox. Route

power cord through exit hole and plug

power cord into a wall receptacle near

firebox.

b. If your firebox installation is recessed

and/or pre-wired, plug power cord into

duplex outlet provided. Refer to your

firebox owner’s manual for instructions

on wiring duplex outlet.

Figure 26 - Attaching Speed Control to

Firebox

Speed Control Control Shaft

Locknut

Control

Knob

Switch

Bracket

Blower

Plug-In

Duplex Outlet

(Located underneath

firebox floor against

lower right outside wall)

Содержание (V)KC36NE series









































Результаты поиска

Содержание (V)KC36NE series

Отзывы:

Похожие инструкции для (V)KC36NE series

Бренды по названию

Популярные бренды

FMI (V)KC36NE series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание (V)KC36NE series

Отзывы:

Похожие инструкции для (V)KC36NE series

Бренды по названию

Популярные бренды