FMI (V)KC36NE series Скачать руководство пользователя страница 25

Страница: 25 / 40

www.fmiproducts.com

116238-01L

Removing Glass Door

If replacement of glass is necessary, entire

assembly, glass and frame, must be replaced.

If glass is broken, wear gloves and tape re

maining fragments onto frame.

1. Remove screen assembly by pushing

the rod either left or right, then down and

forward to remove screen/rod assembly

from firebox. Set assembly aside.

2. Lift up on latches to unlock. There are two

on top of firebox and two below firebox that

hold glass door in place (see Figure 37).

3. While holding glass door to prevent it from

falling and causing injury, remove five

screws from hinge located on left side of

door frame assembly (see Figure 37).

Figure 38 - Removing/Replacing Glass

Door

Lock

Unlock

Glass Frame Assembly

Screw

Hinge

Latch

INSTALLING LAVA ROCK AND

GLOWING EMBERS

It is very important to keep logs exactly as

installed. Do not modify logs. Only use log

set designed for this fireplace. Logs under

log/grate assembly are attached to burner.

Do not attempt to move these logs as this

will damage logs.

WARNING: Logs are unitized

and attached to the grate. Do not

handle log/grate assembly by

logs. Always pick up by grate.

Open louvers, remove screen, unlock door

latches and open glass door. See

Removing

Glass Door

, steps 1 and 2.

1. Pull ember material apart into pieces no

larger than a dime. Place these pieces

loosely and sparingly directly onto ex

posed front section of burner (see Figure

39, page 26). This will create the glowing

ember appearance as flame touches

ember material. Do not block air slots by

using too much ember material in one

area. Place small pieces of ember material

to cover pilot ports. It is not necessary to

use all of the ember material provided.

2. Pour lava rock onto plenum but not onto

flat burner. It is not necessary to use all

of the lava rock provided.

NOTICE: Do not put lava rock on

burner or under burner. Placing

lava rock on burner will cause

performance problems.

3. Close glass door, lock door latches, replace

screen and close louvers (see

Removing

Glass Door

, steps 5 through 7).

WARNING: The glass door

must be securely in place before

running this fireplace. Do not run

this fireplace if glass is missing

or broken.

FIREPLACE INSTALLATION

Continued

4. Remount new frame at hinge with five

new screws before closing door. This will

ensure seating of gasket.

5. Close glass door frame. Lock latches by

placing bar under tab on door and pushing

down and back on latch (see Figure 37,

page 24).

6. Replace screen/rod assembly by revers

ing step 1.

7. Replace louvers by reversing procedure

under

Removing Louver Panels,

page 24,

for KC36 series.

8. Replace screen door assembly, see remov

ing screen door assembly, page 24 see

Figure 37, for (V)KCC36 series.

Cleaning Glass Door

See

Cleaning and Maintenance

on page 30.

Содержание (V)KC36NE series









































Результаты поиска

Содержание (V)KC36NE series

Отзывы:

Похожие инструкции для (V)KC36NE series

Бренды по названию

Популярные бренды

FMI (V)KC36NE series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание (V)KC36NE series

Отзывы:

Похожие инструкции для (V)KC36NE series

Бренды по названию

Популярные бренды