background image

www.fmiproducts.com

116238-01L

28

6.  Wait five (5) minutes to clear out any gas. 

Then  smell  for  gas,  including  near  the 

floor. If you smell gas, STOP! Follow “B” 

in the safety information in column 1. If 

you don't smell gas, go to the next step.

7.  Turn  equipment  shutoff  valve  counter

-

clockwise 

 to the ON position. Do 

not force.

8.  Close lower louver panel.
9.  Turn on all electric power to appliance.
10. Turn wall switch to the ON position.
11. Visually  locate  pilot. The  ignitor  should 

begin  to  spark  and  main  burner  should 

ignite once flame appears at pilot.
•  If  lighting  appliance  for  the  first  time 

each  season,  it  may  take  several  at

-

tempts before the supply gas can reach 

pilot and main burners.

•  If appliance will not stay lit after several 

attempts, follow instructions 

To Turn Off 

Gas To Appliance

 and call your service 

technician or gas supplier.

TO TURN OFF GAS 

TO APPLIANCE

1.  Turn off wall switch.
2.  Turn off all electric power to appliance if 

service is to be performed.

3.  Open lower louver panel.
4.  Remove  front  hearth  brick  and  control 

access panel.

5.  Turn equipment shutoff valve clockwise 

 to OFF. Do not force.

6.  Close lower louver panel.

OPERATION

FOR YOUR SAFETY  

READ BEFORE LIGHTING

 WARNING: If you do not fol-

low these instructions exactly, 

a  fire  or  explosion  may  result 

causing property damage, per

-

sonal injury or loss of life.

A.  This appliance is equipped with an igni

-

tion device which automatically lights 

the pilot. Do not light pilot by hand.

B.  BEFORE  LIGHTING  smell  all  around 

the appliance area for gas. Be sure to 

smell next to the floor because some 

gas is heavier than air and will settle 

on the floor.

 

WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electric switch; do 

not use any phone in your building.

•  Immediately call your gas supplier 

from a neighbor's phone. Follow the 

gas supplier's instructions.

C.  Do not use this appliance if any part 

has  been  under  water.  Immediately 

call  a  qualified  service  technician  to 

inspect the appliance and to replace 

any  part  of  the  control  system  and 

any gas control which has been under 

water.

LIGHTING 

INSTRUCTIONS

NOTICE: During initial operation 

of new heater, burning logs will 

give off a paper-burning smell. 

Orange flame will also be pres

-

ent. Open damper or window to 

vent smell. This will only last a 

few hours.

1.  STOP!  Read  the  safety  information 

above.

2.  Turn off all electric power to fireplace.
3.  Turn wall switch to the OFF position.
4.  Open lower louver panel.
5.  Turn equipment shutoff valve clockwise 

  to  the  OFF  position  (see  Figure 

43). Do not force.

Figure 43 - Turning Equipment Shutoff 

Valve to the OFF Position

Equipment 

Shutoff Valve

Pilot Adjustment Screw

Sensing 

Rod

Pilot 

Burner

Ignitor

Figure 44 - Pilot

Содержание (V)KC36NE series









































Отзывы: