FMI CD36M-LS Скачать руководство пользователя

Страница: 6 / 40

www.fmiproducts.com

125205-01E

PRODUCT FEATURES

These are a few facts that can help you un-

derstand and enjoy your direct-vent fireplace:

• The venting system may be routed to the

outside of your home in several ways. It

may vent through the roof (vertical) or it

may vent to an outside/exterior wall (hori-

zontal). The vent pipe installation is very

important to allow for proper operation.

You must follow the venting instructions

very carefully for either vertical or horizontal

applications.

• This fireplace may be installed in any room

of your house provided all local codes and

these installation instructions are followed.

• A piezo ignitor and ceramic electrode cre

ate spark to ignite the pilot light. It does not

require any matches, batteries or any other

sources of ignition to light the pilot.

• Each time you turn on your fireplace, you

may notice some amount of condensation

on the inside of the fireplace glass. This

is normal and will disappear after 10-20

minutes of operation.

• Your direct-vent gas fireplace system

(fireplace and venting) is a balanced and

sealed gas operating unit. It requires ap-

proximately 10-20 minutes of operating

time before the flame pattern stabilizes.

• This fireplace is equipped with a millivolt

gas control system that does not require

electricity to operate. A piezo ignitor is

provided to light the pilot without using

matches or lighters.

• This model can accept an optional circulat

ing air blower when 120 VAC connection is

supplied. If you plan to install an optional

blower, do not forget to wire the fireplace

outlet when framing.

PRE-INSTALLATION PREPARATION

Mantel Depth Mantel From Top of Opening

(1) 14"

(A) 16"

(2) 12"

(B) 14"

(3) 10"

(4) 8"

(D) 10"

(5) 6"

(E) 8"

(6) 4"

(F) 6"

(7) 2"

(G) 4"

CAUTION: Do not block

required air spaces with insula

tion or any other material. Do not

obstruct the effective opening

of the appliance with any type

of facing material.

CLEARANCES TO COMBUSTIBLES

Minimum clearances to combustibles for the

fireplace are:

• Back and Sides of Fireplace

. . . . . . . . 0"

• Floor

. . . . . . . . . . . . . . . . . . . . . . . . . . 0"

• Perpendicular Wall

. . . . . . . . . . . . . . . 6"

• Front

. . . . . . . . . . . . . . . . . . . . . . . . . 36"

• Top of Standoffs

. . . . . . . . . . . . . . . . . . 0"

6. Have venting system inspected annually

by a qualified service person. If needed,

have venting system cleaned or repaired.

7. Do not use any solid fuels (wood, coal,

paper, cardboard, etc.) in this fireplace.

Use only the gas type indicated on fire

place nameplate.

8. This appliance, when installed, must be

electrically grounded in accordance with

local codes or, in the absence of local

codes, with the

National Electrical Code,

ANSI/NFPA 70.

SAFETY

Continued

9. Do not use fireplace if any part has been

exposed to or under water. Immediately

call a qualified service person to arrange

for replacement of the unit.

10. Do not operate fireplace if any log is

broken.

11. Do not operate fireplace with glass door

removed, cracked or broken.

12. Provide adequate clearances around air

openings.

MANTEL CLEARANCES

Woodwork, such as wood trims, mantles

and other combustible materials should be

placed within the required clearance speci-

fied in Figure 2.

Содержание CD36M-LS









































Результаты поиска

Содержание CD36M-LS

Отзывы:

Похожие инструкции для CD36M-LS

Бренды по названию

Популярные бренды

FMI CD36M-LS, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание CD36M-LS

Отзывы:

Похожие инструкции для CD36M-LS

Бренды по названию

Популярные бренды