FMI CD36M-LS Скачать руководство пользователя

Страница: 5 / 40

www.fmiproducts.com

125205-01E

SAFETY

Continued

Carefully supervise young chil

dren when they are in the room

with fireplace.

Keep the area around your

fireplace clear of combustible

materials, gasoline and other

flammable vapor or liquids. Do

not run fireplace where these

are used or stored.

1. For propane/LP fireplace, do not place

propane/LP supply tank(s) inside any

structure. Locate propane/LP supply

tank(s) outdoors. To prevent performance

problems, do not use propane/LP fuel tank

of less than 100 lbs. capacity.

2. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup-

plier's instructions

• if you cannot reach you gas supplier, call

the fire department.

3. Never install the fireplace

• in windy or drafty areas where curtains

or other combustible (flammable) objects

can make contact with the fireplace front

• in high traffic areas

4. Turn fireplace off and let cool before

servicing, installing or repairing. Only a

qualified service person should install,

service or repair this fireplace. Have fire

place inspected annually by a qualified

service person.

5. You must keep control compartments,

burners and circulating air passages clean.

More frequent cleaning may be needed due

to excessive lint and dust from carpeting,

bedding material, etc. Turn off the gas valve

and pilot light before cleaning fireplace.

Due to high temperatures, the appliance should be located out of

traffic and away from furniture and draperies.

Do not place clothing or other flammable material on or near the

appliance. Never place any objects on the appliance.

Do not use this fireplace to cook food or burn paper or other flam

mable material.

This fireplace reaches high temperatures. Keep children and adults

away from hot surface to avoid burns or clothing ignition. Fireplace

will remain hot for a time after shutdown. Allow surface to cool

before touching.

Содержание CD36M-LS









































Результаты поиска

Содержание CD36M-LS

Отзывы:

Похожие инструкции для CD36M-LS

Бренды по названию

Популярные бренды

FMI CD36M-LS, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание CD36M-LS

Отзывы:

Похожие инструкции для CD36M-LS

Бренды по названию

Популярные бренды